Kuzco Lighting PD331024 Doral Pendant Instruction Manual
- June 13, 2024
- Kuzco Lighting
Table of Contents
Kuzco Lighting PD331024 Doral Pendant
Product Information
- Product Name: Pendant
- Model Number: PD331024
- Manufacturer: Alora Lighting
Product Usage Instructions
- Remove the pendant fixture from its original package.
- Separate the mounting plate (1c) from the canopy (2a) by removing the canopy screws (2b).
- Attach the mounting plate (1c) to the electrical junction box (1a) using the junction box screws provided (1e) in the hardware package.
- Determine the hanging height of the fixture by securing rods (2d) to the canopy (2a) and fixture (3a), after feeding the fixture’s wires through the rods.
- Make proper electrical connections: connect the black wire to hot L, the white wire to neutral N, and the ground wire to GND. Use the wire nuts (1b) provided in the hardware package.
- Attach the socket assembly (3b) to the fixture (3a), followed by the metal washer (5a), rubber washer (5b), glass (5c), bottom rubber washer (5d), nut (5e), and secure with the finial (5f) by threading clockwise. Install the recommended lamp (4a) (lamp not provided) according to the maximum wattage and type mentioned on the socket label.
- Attach the canopy (2a) to the mounting plate (1c) using the canopy screws (2b).
You are now ready to enjoy your pendant fixture.
Technical Support For any technical support or inquiries, please contact:
- Phone: 1.855.855.8926
- Email: technicalsupport@aloralighting.com
Contact Information:
- Canada: 19054 28th Avenue Surrey – BC V3Z 6M3
- USA: 3035 E. Lone Mountain Rd – Las Vegas, NV, 89081
- Website: www.aloralighting.com
TECHNICAL SUPPORT
1.855.855.8926
technicalsupport@aloralighting.com
WARNINGS AND CAUTIONS
- Make sure POWER is COMPLETELY OFF at the fuse box
- Have your fixture installed by a qualified licensed electrician
- Prepare everything in a clear area
- Wear gloves at all times during this installation
- Read instructions carefully before you start assembly
- Keep this installation sheet for future reference
Please Note:
- 120V input
NOTICE
- The important safeguards and instructions outlined in this sheet cannot cover all possible conditions and situations that may occur. It must be understood that caution and certain care factors must be followed. These instructions are provided for your safety and we highly recommend that a licensed, trained electrician install this unit.
- This fixture is designed to be mounted on a correctly installed standard round or octagon box OR through a wiring box with a plaster frame. The box must be securely mounted to the structure of the building. The crossbar and hardware supplied should be used, directly mounting the fixture to the outlet box may make it impossible to correctly align the fixture.
ASSEMBLY INSTRUCTIONS
Step 1
Remove fixture from its original package.
Step 2
Separate mounting plate (1c) from canopy (2a) by removing canopy screws (2b).
Step 3
Attach mounting plate (1c) to electrical junction box (1a) using junction box
screws provided (1e) in hardware package.
Step 4
Determine hanging height of fixture by securing rods (2d) to canopy (2a) and
fixture (3a), after feeding fixtures wires through rods.
Step 5
Make proper electrical connections (black to hot “L”, white to neutral “N”,
ground to “GND”) with wire nuts (1b) provided in hardware package
Step 6
Attach socket assembly (3b) to fixture (3a), followed by metal washer (5a),
rubber washer (5b), glass (5c), bottom rubber washer (5d), nut (5e) and secure
with finial (5f) by threading clockwise. Install the recommended lamp (4a)
(not provided) (referred on the socket label for maximum wattage and type) to
fixture socket.
Step 7
Attach canopy (2a) to mounting plate (1c) with canopy screws (2b).
You are now ready to enjoy your fixture.
P: 1.855.855.8926
CANADA : 19054 28th Avenue Surrey – BC V3Z 6M3
USA : 3035 E. Lone Mountain Rd – Las Vegas, NV, 89081
www.aloralighting.com
20230619