MTX Audio PROXP-20-FS Polaris Rzr Pro Xp Front Speaker Pods Owner’s Manual
- June 9, 2024
- MTX Audio
Table of Contents
PROXP-20-FS Polaris Razor Pro Xu Front Speaker Pods
Owner’s Manual
PROXP-20-FS
POLARIS® RZR ® PRO XP FRONT SPEAKER PODS
OWNER’S MANUAL
PROXP-20-FS Polaris Rzr Pro Xp Front Speaker Pods
THANK YOU
Thank you for making the AWESOME decision to purchase our MTX Audio 6.5″
weatherproof speakers for your Polaris ® RZR ® Pro XP. With a few simple tools
from our trusty toolbox you’ll have these installed in no time. The
rotationally molded enclosures are built as a single piece, designed to take
years of abuse without failure and they install quickly with only minor
disassembly of the vehicle. And of course, who can forget the integrated RGB
lighting in the speakers, because, who doesn’t like things that light up,
right? So, congratulations on your purchase, thanks for your support and most
importantly, enjoy the ultimate audio experience with MTX!
WE’RE HERE TO HELP
We’re here to help with any installation or technical support. Visit
mtx.com to chat, call
1-800-225-5689 to speak with an MTX
Technical Support representative, or visit
youtube.com/user/MTXAudioUSA to view
product videos.
DON’T FORGET TO REGISTER YOUR PRODUCT
Don’t forget to register your new MTX Audio product. Visit
mtx.com/productregistration or scan the
QR code to the right.
Model #…………………………………………….
Serial #……………………………………………..
Dealer’s Name…………………………………..
Date of Purchase………………………………
IMPORTANT NOTICE
Whenever working on the vehicle, it is recommended to disconnect the battery
prior to starting work.
Failure to do so may lead to a risk of electric shock or equipment damage.
When connecting power and ground wires ensure that the red power wire is fused
at the point where it is connected to the vehicle’s battery. Failure to do so
can result in damage to the vehicle if a short circuit develops between the
vehicle connection point and the product.
FEATURES
Tweeter:
- Textron Dome Tweeter for High Output and Accurate Audio Reproduction
- Adjustable Tweeter Attenuation for Fine Tuning of Output
- Tweeter Mounts in OEM Factory Housing
Midrange:
- Fully Assembled and Prewired Enclosure
- Installer Friendly Enclosure Design for Easy Installation
- Integrated RGB Lighting
- Mounts Behind Factory Grille Maintaining OEM Cosmetics
- Utilizes Factory Mounting Assembly
- Compatible with OEM or MTX Subwoofer Installed
SPECIFICATIONS
- RMS Power Handling: 75-Watts
- Peak Power Handling: 150-Watts
- Sensitivity (2.83V/1m): 92dB
- Sensitivity (1W/1m): 87.6dB
- Frequency Response: 70Hz – 20kHz
- Impedance: 3.4Ω
FIT GUIDE
Pro XP / XP4 Sport ……………………………………………………………………….2021 – 2022
Pro XP / XP4 Premium ………………………………………………………………2020 – 2022
Pro XP / XP4 Ultimate ………………………………………………………………..2020 – 2022
Pro XP / XP4 Sport RFLE……………………………………………………………2021
Pro XP / XP4 Ultimate RFLE ……………………………………………………….2021
IN THE BOX
- PROXP-20-FS Speaker Pods and Tweeters
- Mounting Hardware
(2) Mounting Brackets, (1) per Enclosure
(2) T30 Torx Course Thread – 20mm Long
(4) T20 Torx Course Thread – 15mm Long
(8) T20 Torx Course Thread – 29.5mm Long
(8) Zip Ties
DISASSEMBLY
Step 1 – Remove the speaker grille by removing two (2) T-40 TORX bolts.
Note: For vehicles that have the OE speaker pods installed follow these
additional steps for removal.
Step 2 – Remove four (4) T-25 screws found around the front of the
speaker.
Step 3 – Remove two (2) T-27 screws found at the back of the speaker pod on the firewall. Step 4 – Remove one (1) T-40 Bolt from the inside fender well.
Step 5 – Disconnect the speaker pod plug and remove the pod from the
vehicle. Step 6 – Repeat this process on the other side.
Step 7 – With the pods removed, reinstall the T-40 TORX bolt into the fender
well location.
Step 8 – Repeat process for other side of the vehicle.
Step 9 – Disengage the speaker pod from the top of the dash/ fender panel
and slide up the cage tube. Step 10 – Press the dummy plug or OE tweeter
if installed from the front and remove from the enclosure from the rear.
Step 11 – If OE tweeter is installed, disconnect the harness connector.
Step 12 – Repeat process for other side of vehicle.
INSTALLATION
Step 13 – Locate and install the rear support brackets as shown using the supplied four (4) 15mm T-20 TORX screws. Step 14 – Placing the Speaker enclosure against the dash housing from the rear and holding it in place, loosely install four (4) 30mm T-20 TORX screws from the front into the enclosure housing in the predrilled holes.
Step 15 – Align the rear support bracket with the factory screw location in the firewall and install one (1) T-27 TORX screw and tighten.
Step 16 – Tighten the four (4) screws on the front of the enclosure.
Step 17 – Feed the tweeter harness connector up through the top of the dash.
Step 18 – Repeat process for the other side of the vehicle.
Step 19 – Prior to installation, choose your tweeter attenuation
preference, 0dB or -6dB, by moving the jumper found on the back of the tweeter
housing.
Step 20 – Locate and align the key on the body of the tweeter pod to the slot molded into the tweeter opening on the factory housing.
Step 21 – Press the tweeter into the opening from behind until the grille is seated flush with the front of the enclosure.
Step 22 – Connect the harness connector from the lower speaker enclosure to the tweeter harness.
Step 23 – Repeat the process for the other side of the vehicle.
Note: If installing as part of an MTX Thunder kit, route the enclosure
harness to the center of the dash and connect to the labeled connector.
If NOT installing as part of an MTX Thunder kit, the speaker plug will need to
be removed and hardwired. Refer to the below diagram for wiring connections.
Speaker Wire
Gray (+)
Blue (–)
LED Wire
Red
Green
Blue
Black
Once connected, test for function.
Step 24 – Slide the tweeter housing back down and reseat the housing to the
fender and dash panel
Step 25 – Install the supplied MTX badge to the factory grilles with the
supplied hardware.
Step 26 – Reinstall the factory grilles using factory hardware removed
earlier.
Step 27 – Reassemble and go ride.
NOTES
WARRANTY PERIOD
At MTX Audio we engineer products that will stand up to the test of time. We
also realize that from time to time a problem may occur. That’s why our
products carry a 2- year limited warranty that begins at the time of sale to
the end user.
Of course, we’re here to help. If you experience an issue with any of our
products within the warranty period, please contact our customer service
technical line at 1-800- CALL-MTX to help troubleshoot your issue. If, after
speaking with our technical experts it is determined that a problem lies with
the product, the technician will provide you with a Return Authorization
number and all relevant details you’ll need to get the product taken care of.
MITEK WARRANTY
MiTek Mobile products (including, but not limited to: MTX, Caustic,
Streetwise, Extant, Bass Slammer, and Thunder Marine) purchased in the USA
from an UTHORIZED MITEK DEALER are guaranteed against defects in material
and workmanship for the period of time specified. The warranty period begins
the day the product is purchased by the end user, and this warranty is
limited to the original retail purchaser of product. Products found to be
defective during the warranty period will be repaired or replaced with
equivalent product by MiTek at no charge. This warranty is void if it is
determined that unauthorized parties have attempted repairs or alterations of
any nature, and the warranty does not extend to cosmetics or finish. MiTek
disclaims any liability for other incurred or consequential damages resulting
from product defects. MiTek’s total liability will not exceed the purchase
price of the product.
Let’s Get Social
mtx.com
Like, Follow, & Subscribe
© 2021 MiTek Corporation. All rights reserved.
MTX is a trademark of MiTek Corporation. All other trademarks
are property of their respective owners. Designed and Engineered in the U.S.A.
Due to continual product development, all specifications are subject to change
without notice.
MTX Audio, 4545 East Baseline Rd. Phoenix, AZ 85042 U.S.A.
1-800-225-5689
MTX006856 Reva 12/21 • AW0016029 • 1-14927
MTX.COM
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>