FLINQ FQC8181 Alume True Wireless Earbuds User Manual

FLINQ FQC8181 Alume True Wireless Earbuds

Thank you for purchasing this product of FlinQ! To ensure continuous operation and accuracy, please read these operating instructions carefully before use and save this manual for future use. Passing certain procedures may result in incorrect use. We hope that you will enjoy using your new FlinQ product! If by any chance the item is damaged, defect or broken, you are covered by warranty! Please do not hesitate to contact us for any questions, concerns or suggestions at the email address mentioned in this manual.

Specifications

TWS (True Wireless Stereo); Elite wireless design, individual channel left and right, HIFI True stereo sound with deep bass quality.Both the left and right earbuds are connected via Bluetooth. These can be used individually or as a pair.

Bluetooth version:

|

V5.0+EDR low using

---|---

Bluetooth mode:

|

A2DP1.3/HFP1.6/HSP1.2/AVRCP1.6/D11.3 Stereo mode

Bluetooth frequency:

|

2.4 ~ 2,485 Ghz

Bluetooth range:

|

+- 10 meters in open space

IP Grade:

|

IP-X3 splash proof

Battery status indicator support:

|

yes. *

Speaker driver frequency:

|

20 ~ 18000 Hz

Talk/playtime 1 set of earbuds (L+R) mode:

|

3 – 3.5 hours max.*

Stand by time 1 set of earbuds (L+R) mode:

|

80 – 120 hours max.*

Charge time docking case:

|

90 minutes max.

Charge time for earbud(s):| 90 minutes max.

Docking case capacity to re-charge the earbuds:

| 5 times max. for both earbuds, or 10 times for a single earbud.

AUTO ON/OFF

This product is made with an auto sensor switch to turn the earbuds on and off automatically when you open or close the lid from the docking case. Open the lid is auto ON, close the lid is auto OFF.
TIP: The earbuds can also be manually set ON and OFF by the touch sensor button.

Pairing

1. Pair with 1 earbud:

   • Open the docking case, the sensor switch will power it on, then the left and right earbuds will be paired to each other automatically. Then choose 1 of the 2 earbuds and close the case.
   • Turn on Bluetooth on your mobile device and select “FlinQ Alume True Wireless Earbuds” from the list. You will then hear a voice that says that you are“connected”. From now on you can listen to music and you are able to receive calls. The Elite Wireless earbuds also supports incoming calls.
     *Note: During phone calls only 1 earbud works (depends on phone brand and / or model), you can keep the other earbud in the charging dock. When take out the other earbud to use, the both earbuds will connect each other automatically to be synchronized including the memory function.

2. Pair with both earbuds:
   

   • Open the docking case, the sensor switch will power it on, then the left and right earbuds will be paired to each other automatically. Take out both of the 2 earbuds, the right earbud work as host.
   • Then enable Bluetooth on your device and select ” Flinq Elite Wireless Earbuds” from the list. When the LED light slowly blinks blue, the earbuds have been successfully connected. The battery status is visible on your mobile phone (if supported).
   • You will hear the message “connected” for verification.

Note:
During phone calls two earbuds work, and on both sides you can control Power off/Play/Pause individually during the connection. The other earpiece is then synchronized. The memory function is
automatically supported when reconnecting both devices (both earbuds and the device) that were used last time!

Bluetooth use

1. Making phone calls:
   Make sure the earbuds are connected to your mobile device. You can call now. With phone calls, 1 or 2 of the earbuds works. You will hear the telephone number when you receive a call. You answer the call by pressing the right or left touch button once. To reject the call, press 2x quickly the right or the left touch button so the call is rejected. When the earbuds are in music or standby mode, you can call the last telephone number again by pressing the right touch button 3x quickly. You can change the volume by pressing the touch button 2x shortly on the right headset for volume + and 2x shortly on the left touch button headset for volume – or change it by the volume buttons from your device directly. For Apple users that use SIRI: 3x quickly press on the left multifunction button headset to activate it.

2. Listen to your music
   Make sure that the earbuds are connected to your mobile device. You can now listen to the music on your playlist. 1x short press the touch button to stop the music. Press the button again to continue. Long press the right touch button till the beep is heard for the next song and long press the left touch button till the beep is heard for the previous song.

3. .Power off
   Hold down the touch button until the LED light shows red. The Bluetooth device switches off, even when the earbuds are both connected as a set. If the earbuds have been removed from your Bluetooth device for more than 5 minutes, they will switch off automatically. You do not have to worry about an empty battery.

4. Charging
   You will hear a reminder sound when the battery is low. At the same time, the LED light will turn red on the earbuds. Place the earbuds inside the docking case and close the lid. During charging, the LED light turns red (to check open the lid a little bit to see the leds working), and it switches off automatically when it is fully charged. If both earbuds are empty and also the docking case, please re-charge the docking case at first with the micro usb charge cable. The docking case will be charged firstly (led with flash 1,2,3 till 4 leds all will ON 1 by 1 till full) and when full it will automatically charge the earbuds till full (led will be ON from 4, 3, 2 till 1 led 1 by 1 till empty) and then switch auto off.

Note: the earbuds will be switched off automatically during charging.

Warning

1. Do not use the earbuds excessively and do not store them under heavy pressure. The earbuds are not resistant to heat and water.
2. Keep the earbuds away from the WIFI router or other high-frequency equipment and walls etc. to prevent interruption of signal reception.
3. Use the earplugs in working range (max. 10 meters). The effect will be significantly better if there are no obstacles between the connected devices.
4. Use these Bluetooth earphones with any device with Bluetooth stereo function.
5. Do not press the earbuds too hard into the charging station if you want to charge them! A soft “magnetic click” indicates that they have been placed correctly. The LED light turns red when charging starts.
6. When using the earbuds again, please keep them upright when you remove them from the charging station to prevent damage.

Highlights

1. Dust-proof mesh
2. Multifunction button
3. Microphone
4. Charging connection point
5. LED light charging station
6. Type-C charging port

(Waste Electrical & Electronic Equipment) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household user should contact either the retailer where they purchased this product or their local government office for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.

Disclaimer

Information in this document is subject to change without notice. The manufacturer does not make any representations or warranties (implied or otherwise) regarding the accuracy and completeness of this document and shall in no event be liable for any loss of profit or any commercial damage, including but not limited to special, incidental, consequential or other damage. No part of this document may be reproduced or transmitted in any form by any means, electronic or mechanical, including photocopying, recording or information recording and retrieval systems without the expressed written permission of the manufacturer.

Warranty

The warranty begins on the date of purchase and expires after 24 months. The warranty period is considered to have started three months after the date of manufacturing indicated on the product o as derived from the serial number of the product If any defect due to faulty materials and/oi workmanship occurs within the warranty period. FlinQ will make arrangements for service. Where a repair is not possible or is deemed uneconomical FlinQ may agree to replace the product. Replacement will be offered at FlinQ discretion and the warranty wili continue from the date of original purchase. The FIinQ warranty applies provided the product has been handled properly for its intended use and in accordance with the operating instructions. Warranty information: klantenservice@flinqcommerce.nl

References

• 2020 - Agentur für Nachhaltigkeit und Kommunikation |
• FlinQ Commerce is de online non-food groothandel uit Eemnes

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>