HOOKE ROAD BXG.3053 JL Flux Front and Rear Fender Flares Kit User Manual
- June 17, 2024
- HOOKE ROAD
Table of Contents
HOOKE ROAD BXG.3053 JL Flux Front and Rear Fender Flares Kit
Product Information
Specifications
- Model: BXG.3053
- Contents:
- Front Flares:
- 4 x M8*20 Button Head Socket Cap Bolts Screws
- 12 x M6*20 Button Head Socket Cap Bolts Screws
- 12 x Split Lock Washer D6 M8161
- 12 x Flat Washer M6161
- 10 x Flange Hex Lock Nuts M6
- 4 x Flange Hex Lock Nuts M8
- 2 x Rivet Nut M6
- Rear Flares:
- 12 x M6*35 Button Head Socket Cap Bolts Screws
- 12 x Split Lock Washer
- 12 x Flat Washer
- 4 x Flange Hex Lock Nuts
- 8 x Rivet Nut D6 M6161
- 6 x Flange Hex Lock Nuts M6
Frequently Asked Questions
- Q: What is the installation time for these fender flares?
- A: The installation time is about 1.5 hours, and it may require 2-3 people depending on mechanical skill level.
- Q: Do I need any special tools for installation?
- A: Yes, tools required include Drive Socket Ratchet Wrench, 4mm & 5mm Hex Bit Socket, Rivet Nut Tool, 10mm & 13mm Wrench, and Hand Rivet Nut Tool (included).
Contents
Tools
Tools required
- a. Drive Socket Ratchet Wrench;
- b. 4mm & 5mm Hex Bit Socket;
- c. Rivet Nut Tool;
- d. 10mm & 13mm Wrench;
- e. 10mm Shallow Socket;
Installation time
- About 1.5 hours, 2-3 people may be needed. Installation time may differ according to your mechanical skill level.
- (PLEASE VERIFY ALL PARTS ARE PRESENT AND READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION!)
- To view the electronic version (BXG.3053), please scan the QR code.
Installation Instruction
Passenger Side Front Fender Flare Installation:
- Step 1: Before installation, please remove the factory fender liners in preparation for installing our product.
- Step 2: Due to the inability to install nuts in the side screw holes, you need to manually insert a rivet using a hand riveting tool at the side mounting location. the rivet nut tool instruction: Place the nut or insert into the hole, making sure it fits snugly. Position one end of the hand rivet tool onto the nut or insert, and use the tool’s handle to squeeze and compress it. This will create even pressure around the nut or insert, securing it firmly in place. Once finished, you can thread a bolt or screw into the nut or insert to securely fasten objects together.
- Required Tools: 10mm Shallow Socket & 10mm Wrench;
- Required Tools: 10mm Shallow Socket & 10mm Wrench;
- Step 3: Next, it is recommended to begin by installing the side holes. Lift the fender flare to align it with the side holes, then secure it in place directly using M6*20 hex socket screws and nuts. No nuts are required for the holes where rivets have been used.
- Step 4: Before installing the front holes, please differentiate between the left and right brackets. It is recommended to compare all four brackets together. The brackets are symmetrical, and the direction of brackets 1 and 2 is opposite. Bracket 1 faces the left side, while bracket 2 faces the right side.
- Step 5: Once you’ve confirmed the bracket positions, proceed to install the front four holes. For the first two holes, secure them directly using M620 hex socket screws and nuts. As for the remaining two holes, use the identified connecting brackets from the previous step. Attach them to the vehicle using the same screws and nuts, with M820 screws and nuts on the other side of the bracket.
Passenger Side Rear Fender Flare Installation:
- Step 6: Before installation, please remove the factory fender liners in preparation for installing our product.
- Step 7: Please verify the side installation holes based on the labels in the image. All of these holes require rivet installation, so you will need to perform the same riveting procedure as described in step 2 for the four holes.
- Step 8: After installing the rivets, you can proceed to install our rear fender flare. Secure it in place using M6*35 screws for all holes. There’s no need for nuts in the holes where rivets have been used on the side.
- Step 9: After completing the passenger side installation, follow the same installation method on the driver side.
Lighting Wiring Installation:
Step 10
- The installation is complete. We hope you enjoy a wonderful off-road life with this quality Hooke Road product.
Attention
- The product parts in this instruction may differ slightly from the actual product contents but generally does not affect the installation of the product.
- Please feel free to contact your distributor if you have any kind of question about your purchase.
Google Hooke Road to find your parts
- Feel Free To Share Your Vehicle @HookeRoad4x4 With The Hashtag #hookeroad If You’d Like.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>