Z-Lite 7504P24 Hanging Light Instruction Manual

Z-Lite 7504P24 Hanging Light

Product Information

Specifications

• Installation: Requires basic wiring skills
• Materials: Metal, Glass
• Power Source: Electric

FAQ

• Q: Can this fixture be installed on a ceiling with a radiant type heating system?
  • A: No, it is not recommended to install this fixture on such ceilings as stated in the safety instructions.
• Q: What type of bulb should be used with this fixture?
  • A: The manual does not specify a particular bulb type. However, do not exceed the maximum capacity recommended on the socket.

Product Usage Instructions

Installation and Safety Instructions

Before starting the installation process, ensure that the electricity to the wires you are working on is shut off. This can be done by removing the fuse or shutting off the circuit breaker.

Follow these general guidelines:

1. No special tools are required for installation.
2. Follow the steps in the given order.
3. Avoid hanging the fixture on house electrical wires or installing it on a ceiling with a radiant type heating system.
4. If unsure about the installation process, consult a qualified electrician.

Fixture Assembly

When assembling the fixture:

1. Remove the fixture from the package and ensure all parts are included.
2. Do not misplace any screws or parts needed for installation.

Final Assembly

1. Connect the wires carefully and tuck them inside the outlet box.
2. Raise the canopy to allow mounting screws to protrude through the hole and secure with ball nuts.
3. Install the glass panel and light bulb following the recommended maximum capacity.

Cleaning

To clean the fixture:

• Wipe with a soft cloth.
• Clean glass with a mild soap; avoid abrasive materials.

Ordering Parts

• Keep the instruction sheet for future reference and parts ordering. Use the exact wording from illustrations when ordering replacements.

SAFETY INSTRUCTIONS

FOR YOUR SAFETY WARNING

BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE IS REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF. GENERAL You don’t need special tools to install this fixture. Be sure to follow the steps in the order given. Under no circumstances should a fixture be hung on house electrical wires, nor should a swag type fixture be installed on a ceiling which contains a radiant type heating system. Read instructions carefully. If you are unclear as to how to proceed, consult a qualified electrician.

NOTE: Proper wiring is essential for the safe operation of this fixture.

GENERAL

You don’t need special tools to install this fixture. Be sure to follow the steps in the order given. Under no circumstances should a fixture be hung on house electrical wires, nor should a swag type fixture be installed on a ceiling which contains a radiant type heating system. Read instructions carefully. If you are unclear as to how to proceed, consult a qualified electrician.

NOTE

• Proper wiring is essential for the safe operation of this fixture.

FIXTURE ASSEMBLY

Carefully remove the fixture from the carton and check that all parts are included as shown in figure. Be careful not to misplace any of the screws or parts which are needed to install this fixture.

• STEP 1: Screw the rod (N) into the fixture top coupling, and add the rods (M), (L) (K), (J), (I), (H), (G) to get your desired height of the fixture, and thread the canopy swivel (F) into the upper rod.

INSTALLATION

IMPORTANT: Do not attach fixture directly to outlet box.

• STEP 1: Thread mounting screws (A) into the match holes of Circular strap (B).
• STEP 2: Secure circular strap (B) to outlet box with outlet box screws (C).
• STEP 3: Hook the steel cable from the fixture canopy to the circular strap(B), then, make the wire connections.

GROUNDING INSTRUCTIONS

• STEP 1: Insert the green grounding screw into the hole with two raised dimples on the mounting bar. Wrap the ground wire from the fixture (if supplied) around the green grounding screw, then connect it to ground wire from the outlet box (if not fixed on the outlet box) using a wire connector (not supplied). If ground wire from the fixture is not supplied, wrap the ground wire (if not fixed on the outlet box) from the outlet box around the green grounding screw and tighten it. NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES.
• STEP 2: Take note of the color of the wire(s) on your fixture. Identify which group your fixture wire(s) falls into and connect the wires according to the directions below:
  GROUP A: Connect to Black  House Wire| GROUP B: Connect to White House Wire
  ---|---
  BLACK| WHITE
  *PARALLEL WIRE ( round &

smooth)

| *PARALLEL WIRE ( square & ridged)
WHITE OR GREY WITH TRACER| WHITE OR GREY

WITHOUT TRACER

BROWN GOLD OR BLACK WITHOUT TRACER| BROWN, GOLD OR BLACK WITH TRACER

• NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer wire is square shaped or ridged and the less tracer wire is round in shape or smooth (seen best when viewed from wire end.)
• STEP 3: Take your fixture wire(s) from group A and place evenly against the black wire from the outlet box. Do NOT twist wires together before using wire connectors.
• STEP 4: Fit a wire connector over the wires and screw the connector clockwise until you feel firmness.
• STEP 5: Try gently to pull the connector off the wires. If you can pull the connector off, carefully re-do steps 3 and 4 as above, and check again for a firm connection.
• STEP 6: Connect the fixture wire from group B to the white wire from the outlet box in the same manner. Make sure no bare wires can be seen outside wire connectors.

FINAL ASSEMBLY

• STEP 1: After wires are connected, tuck them carefully inside outlet box. Raise canopy (D) allowing for the mounting screws (A) to protrude through the hole on canopy (D), then, secure with ball nuts (E).).
• STEP 2: slide the Glass panel (O) into the fixture frame(P) from the top opening.
• STEP 3: Install light bulb from the fixture bottom (Bulb not included) (Please do not exceed the maximum capacity recommended on the socket.)

CLEANING

• To clean wipe fixture with a soft cloth. Clean glass with a mild soap.
• Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

ORDERING PARTS

Keep this sheet for future reference, and in case you need to order replacement parts. Be sure to use exact wording from illustration when ordering parts.

• Line art shown may not exactly match the fixture enclosed.
• However, the installations do apply to this fixture.

ITEM NO: 7504P17 7504P24 7504P32

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>