ELKAY EF3000VRBMC Water Dispensers Instruction Manual

: June 17, 2024
: ELKAY

Table of Contents

EF3000VRBMC Water Dispensers
INSTALLATION STEPS
OPERATING INSTRUCTIONS FOR THE FILTER MONITOR
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Installation Manual
EF3000VRBMC
3000 Gallon Vandal-Resistant Filtration Kit with Filter Status Monitor

EF3000VRBMC Water Dispensers

IMPORTANT NOTE – To avoid danger of an electric shock hazard, disconnect power to your unit before installing the ﬁ lter.

IMPORTANT THIS IS INTENDED FOR AN INDOOR APPLICATION ONLY.
THIS IS FOR USE ON COLD WATER ONLY.
ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON.

TOOLS REQUIRED
BUT NOT PROVIDED:
– SAFETY GLASSES
– GLOVES
– LEVEL
– PENCIL
– MOUNTING SCREWS, ANCHORS, FASTENERS

INSTALLATION STEPS

Before starting your installation, verify that you have the following included pieces.
a. 1 Pinned Torx Bit
b. 2 AA Batteries
c. 1 Pinned Torx Screw
d. 3.5 Feet of Poly Tubing
Find a location to mount your new ﬁlter box near the water dispenser to which it is being connected. For accurate monitoring, the ﬁlter box should be mounted vertically as shown (Fig. 2, page 2). NOTE: All installations must be compliant with ADA regulations.
Shut oﬀ the water and electricity to the water dispenser.
Lift the cover at the bottom and slide upwards toward the top.
Take the ﬁlter box and place on the wall in the desired location. Be sure that the box is positioned vertically on the wall as shown. The arrow on the water monitor valve should always be pointing UP (Fig. 4). Make sure the ﬁlter box is level, take a pencil and mark around the inside opening and the mounting locations. If the water will not be coming thru the wall into the back of the ﬁlter box, knock-outs have been provided to allow the water lines to run thru the sides or bottom. NOTE: If running the water lines thru the knockouts, use the appropriate protection (not provided) to keep the lines from getting cut.
BOTTOM OF ENCLOSURE MUST BE LEVEL
Cut a hole in the wall anywhere inside the marked location to allow room for the water lines to come into the back of the box. Alternately the box can be mounted inside a wall by marking the outside of the box and cutting a hole slightly larger than the enclosure. This will, if desired, reduce the projection from the wall surface
Remove any protective covering from the outside of the ﬁlter box.
Using the appropriate fasteners (Not Supplied), mount the box to the wall.
Disconnect the water inlet from the water dispenser or water supply and connect to the inlet copper tube on the ﬁlter head.
Connect the poly tubing from inlet of the water dispenser or faucet to the outlet ﬁtting on the ﬂ ow meter
Remove the red cap from the ﬁlter and install on the ﬁlter head turning clockwise.
Remove the ﬁlter monitor from the back of the box and insert the supplied batteries. Once installed, the monitor will light up. The monitor can now be put back on the back of the box.
Make sure it is positioned so that it can be viewed thru the window in the front cover once it is installed.
Turn on water supply and run water through the product to purge air and ﬁ ne carbon particles from ﬁlter the before use. Visit elkay.com/ﬁltration for additional details.
Carefully inspect all water connections for leaks. Repair as needed.
After peeling the protective covering from the front cover, hook the tab on the top into the slot on the top of the box. Slide the cover down and install the supplied screw. Once done keep the bit as it will be needed for replacing the ﬁlter.

OPERATING INSTRUCTIONS FOR THE FILTER MONITOR

The ﬁlter monitor backlight automatically turns on when there is water ﬂ owing through it. The blue backlight will turn oﬀ after approximately 10 seconds but will display the remaining capacity the entire time water is ﬂ owing. To conserve battery life, the display will automatically turn oﬀ in 10 seconds when there is no water ﬂ owing. The power of the two batteries will last for approximately one year.
The ﬂ ow meter will generate an audible alert and the digits on the LCD will blink red when the remaining capacity reaches zero.
To reset, press the reset button for four seconds. The “RESET” on the LCD will blink twice and the remaining capacity will reset to the originally programmed value.
When the battery power is low the monitor generates an audible alert and the empty battery symbol on the upper right corner will blink. The alert status will be released when the batteries are replaced. NOTE: data from the last status will be memorized when powered oﬀ .
Programming Filter Monitor Capacity Press “PROG” button, until “PROG” blinks on the LCD screen. Then press “RESET” to program the ﬁlter gallon capacity. Scroll to select each number within the gallon capacity. Once the ﬁrst number is chosen, press the “PROG” button to save the number and go to the next digit. Repeat the above process to program up to ﬁve digits from right to left.