ELKAY EZLMSN-EDFPVM214DK Fountain with Vandal Resistant Bubbler User Manual

ELKAY EZLMSN-EDFPVM214DK Fountain with Vandal Resistant Bubbler

INSTALLER

CAUTION: Review these instructions before beginning installation. Be sure that the installation conforms to all plumbing, electrical and other applicable codes.
WARNING : When installation is complete, ensure these instructions are left in the plastic bag provided inside the installed unit for future reference.
WARNING: Service to be performed by authorized service personnel only.

NOTE: It is common practice to ground electrical hardware such as telephones, computers and other devices to available water lines. This can, however, cause electrical feedback in the plumbing circuit, which results in an “electrolysis” effect occurring in the fountain. This may result in water that has a metallic taste to it or has a noticeable increase in the metallic content of the water. When inspecting the plumbing circuit, remember the line may be grounded some distance from the installation and may occur outside the building or area in which the unit is being installed. This condition can be avoided (in most cases) by using recommended materials during installation. Any drain fittings provided by the installer should be made of plastic which will electronically isolate the fountain from the remainder of the building’s plumbing circuits.

REDUCE HEIGHT BY 3 INCHES FOR INSTALLATION OF CHILDREN’S ADA FOUNTAIN
NEW INSTALLATIONS MUST USE GROUND FAULT CIRCUIT INTERRUPTER GFCI)

Figure 1 – Rough-in Dimensions

REQUIRED TOOLS AND MATERIALS

These tables show special tools and/or additional materials (not provided) that are necessary to complete the installation of these units:

1. Make water supply connections (Fig. 10). Install a shut-off valve and union connection to the building water- supply (valve and union not provided). Turn on the water supply and flush the line thoroughly.
   Caution: DO NOT SOLDER tubes inserted into the strainer or filter head as damage to the o-rings may result.

2. Install mounting frame (instructions supplied with mounting frame.)

3. (For LZLMSN-EDFPVM214DK) Install the filter head to the bracket, then the install filter breathe ticket on the mounting frame (Fig. 8), plumb from the filter outlet using the ¼” elbow, poly tubing and ¼ x ¼ x ¼ tee, and the install filter.

   • (For EZLMSN-EDFPVM214DK) Install ¼* tee, copper tubing and strainer per (Fig. 2the ).

4. Hang main panel on the mounting frame hanger. Make sure the podoes tube does not get pinched between the panel & mounting frame. Ensure the panel engages at the top. Align fountain holes with mounting frame holes.

5. Remove the protective coating from the main panel.

6. In the talling water Dispenser Place the unit into the stainless panel and frame. Align the holes in the water dispenser with the nuts in the panel. Attach the dispenser- er to the panel using four (4) supplied 1/4 x 20 screws.

Connecting Catch Basin Waste Drain

Installing the drain is highly recommended to prevent basin overflow. The following steps cover the installation of the drain.

1. Remove the two screws attaching the drain basin to the water dispenser. Remove the drain basin.

2. Place the drain basin on a flat, hard surface, such as a piece of sacrificial wood. Carefully drill a hole in the basin using a 1″ hole saw using a dimpled dimple as a guide to centre the hole saw.
   Note: Do not use a 1-1/8″

3. Trial fit the strainer. If the strainer does not fit, carefully open the size of the hole. If it fits well, place a small amount of plumber putty around the lip of the strainer flange and insert it into the hole.

4. Install the O-ring over the strainer threads.

5. Thread the strainer into the drain adapter. Needle-nose pliers can be used to hold the drain adapter from the top while tightening. Ensure that the connection creates a watertight seal. The drain adapter must be facing to the left.
   Note: Twisting the strainer instead of the drain adapter can compromise the seal created by the plumber’s putty.

6. Attach one end of the 3/4 inch flexible drain hose to the 3/4 inch barbed drain adapter connection using the supplied hose clamp. The supplied flexible drain is 13 inches long. If a longer drain hose is required, it must be installer-supplied.

7. Place the drain basin back into the water dispenser and reinstall the two screws.

8. Connect the drain adapter to the household waste drain pipe. If the p-trap is located inside a sealed wall, it must have permanently glued joints. If the p-trap is in an accessible location, a standard non-glued p-trap is acceptable. Install the water dispenser’s front cover.

9. Line up the front panel with the dispenser frame and attach using the flathead screws and a 3/32” hex wrench.

10.  Install the metal grate cover using the 4 Screws.
    N ote: Always consult local plumbing codes before installation.

LZLMSN-EDFPVM214DK

1. the Install fountain with (4) 5/16-18 HHMS & (4) 5/16-18 nuts (provided) (Fig. 5). Connect the ¼” water linthees from the fountain to the remaining opening on the tee (cut line to fit as needed).

2. Attach waste tubes (1-1/4” O.D.) to 1-1/4” O.D.slideetrapp. Trap on the bottle filler side must be 1-1/2” O.D. (provided by others).

3. Make final water supply connections.

4. These products are designed to operate on 20-105 PSI supply line pressure. If inlet pressure is above 105 PSI, a pressure regulator must be installed in the supply line.
   Caution: Any damage caused by connecting these products to a supply line with pressure lower than 20 PSI or higher than 105 PSI IS NOT covered under warranty.

5. Verify proper dispensing from the bottle filler by Placing a cup, under the water dispenser suppressing pressing the button and verifdispenseispenses.
   Note: the first initial dispenses might have air in the line which may cause a sputter. This will be eliminated once all air is purged from the line. A steady stream of water ensures all air is removed. Check for leaks.

6. Check stream height from the bubbler. Stream height is factory set for 35 PSI supply. If supply pressure varies greatly from this, remove the push button (Item 5 – Fig. 8) and adjust the screw on the regulator (Item 4 – Fig. 8). Tothe remove push button, loosen the set screw (Item 7 – Fig. 8) on bottom of the sleeve (Item 6 – Fig. 8) and pull it out on the button. Clockwise adjustment will raise stream height and counterclockwise movement will lower stream height. For best adjustment stream should hit the basin approximately 6-1/2” from the bubbler. Reassemble the push button by pushing in on the button and tightening the set screw (Item 7 – Fig. 8) in the sleeve (Item 6 – Fig. 8).

7. Install the bottom cover platethe on the fountain (Fig. 4).

8. Tighten back panel screws (Item 9 – Fig. 4).

9. Optional: Mount optional panels. Mount the ticket on the wall per rough-in instructions. Slide the tongue of the panel under the edge of the already installed panel. Tighten screws. Once the installation is complete, the water has been turned on, and any trapped air has been bled from the system re-check for any water leaks.

Once the installation is complete, the water has been turned on, and any trapped air has been them the system re-checks for any water leaks.

Figure 6 – Bubbler Details

NOTE:
When installing the replacement bubbler and pedestal, tighten the locknut only to hold the parts snugly in the p position. Do Not overtighten.

PARTS LIST

Installation Package
The components for installation are packed in three separate boxes, regardless of the type of unit being installed. The boxes contain the following:

• Box No. 1: Wall Frame(s)
• Box No. 2: Fountain(s), Arm(s) and Panels
• Box No. 3: Water Dispenser

Additional materials, as noted in the Parts List, are also shipped in these boxes.

TROUBLESHOOTING & MAINTENANCE

Orifice Assembly: Mineral deposits on the orifice can cause water flow to spurt or not regulate. Mineral deposits may be removed from the orifice by poking with a small round file not over 1/8” diameter or using a small diameter wire. DO NOT file or cut orifice material.
Stream Regula tor: the If orifice is clean, regulate flow as in Step 14 of the installation instructions. If replacement is necessary, the see parts list the for correct regulator part number.

Actuation of Quick Connect Water Fittings: The Cooler is provided with lead-free connectors that utilize an o-ring water see al. Toe remove the tubing from the fitting relieve the water brand essure, and push ingreythe grey collar while pulling on the tubing. (See Fig. 11) To insthetheg, push the tube straigfittuntilntil it positive stoptivestop ( approximately 3/4”).

OR PARTS, CONTACT L OCAL DISTRIBUTOR OR CALL 1.800.834.4816REPAIR SERVICE INFOTOLLFREEROLLL FREE NUMBER 1.800.260.6640

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>