ELKAY LK4400BF Series Outdoor ezH2O Bottle Filling Station Pedestal Owner’s Manual

: June 6, 2024
: ELKAY

Table of Contents

INSTALLATION INSTRUCTIONS
TOOLS REQUIRED (NOT PROVIDED)
Parts List
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Owners Manual
Outdoor Bottle Filler Foot Pedal Accessory
For Use On Following Series Fountains With Floor Mount Base

Elkay Series:
LK4400BF
LK4420BF1U
LK4420BF1UDB

Halsey Taylor:
4400BF
4420BF1U
4420BF1UDB

Installer
To assure you install this accessory easily and correctly, PLEASE READ THESE SIMPLE INSTRUCTIONS BEFORE STARTING THE INSTALLATION. CHECK YOUR INSTALLATION FOR COMPLIANCE WITH PLUMBING, ELECTRICAL, AND OTHER APPLICABLE CODES.

INSTALLATION INSTRUCTIONS

Shut off the water to the fountain. Press the push button(s) to relieve the remaining water pressure from the unit.
Using the supplied T-27 Torx head bit and a bit holder, remove all 8 screws securing the upper and lower access panels located on the side of the fountain. See Fig.7 and 5.
Note: Foot pedal will replace the lower access panel.
Through the lower access panel opening, locate the 3/8″ water inlet copper tube at the bottom of the fountain and cut it, leaving enough on both sides to insert the supplied 3/8″ Tee.
Take one of the 3/8” Tees and insert the copper tube, in-line strainer, and 6” of the ¼” poly tubing as shown. After assembled, attach the 3/8″ Tee to the 3/8″ water inlet copper tubing where it was cut in Step 3. See Fig.1 and 6.
Take the ¼” poly tubing from the water line assembly and insert it into the inlet side of the regulator on the foot pedal. See Fig.2 and 6.
Take the remaining supplied 3/8” Tee and connect one end of the 3/8” poly tubing into it as shown. See Fig.3 and 8.
Slide the black insulation onto the 3/8″ poly tubing and then cut off the remaining insulation at the end of the tubing.
Connect the 3/8″ poly tubing to the 3/8” x ¼” fitting. Cut another ¼” poly tubing to 6 inches and then insert it into the open end of the fitting. See Fig.4 and 6.
Looking into the fountain from the upper access panel, locate the 3/8″ water line leading from the bottle filler push button to the bottle filler; cut it, leaving enough on both sides to insert the supplied 3/8″ Tee. See Fig.3, 7, and 8.
Place the 3/8″ poly tubing inside the fountain body and arrange it to be accessible from the lower access opening. Take the ¼” poly tubing and insert it into the regulator. See Fig.6.

TOOLS REQUIRED (NOT PROVIDED)

Gloves
Safety Glasses
Tubing Cutter
Utility knife
Bit holder
|
---|---

Parts List

ITEM NO.	DESCRIPTION

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16| Assy, 4481 FP Foot Activation
Washer-Spacer 2.00 O.D.
Nut-Hex 1-5/16″
1-1/8″-24 Retaining Nut
Regulator – High Flow Wars
Holder – Regulator
Sleeve – Push Button Guide
Button – Push w/o Hole
Tube-Poly 1/4″X.040 Wall
Strainer – In-Line Wras
Tube – Cu 3/8″ X 4.75 (1-P117)
Fitting Tee – 3/8″
Fitting – Union-3/8″ X 1/4 Union
Tube-Poly 3/8″X.062 Wall
Screw-Cap #6-32
Insulator-Tube 3/8″-3/16 Bulk
ITEM NO.| PART NO.| DESCRIPTION
---|---|---
17
18| 1000006235
1000006234| 4481FP – Outdoor Fountain Foot
Activation – Push Button Service Kit
4481FP – Outdoor Fountain Foot
Activation – Regulator Service KIT