Elkay WSF6000R Water Sentry Replacement Filter for Bottle Fillers Instruction Manual

Elkay WSF6000R Water Sentry Replacement Filter for Bottle Fillers

Genuine Elkay filters are tested and certified by NSF International to NSF/ANSI 42 and 53 for the reduction of Chlorine, Taste and Odor, Particulate Class I, and Lead.
(NOTE: CTO replacement filter is only certified to NSF 42 claims; see WSF6000R Performance Data Sheet for additional information.) These filter kits are designed to be used with the following Elkay products.

Filtered EZH2O® Bottle Filling Station Models
Examples include but are not limited to LZWS, LZSWS, LVRCWS, LMABFWS
NOTICE: Do not use water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. A filter must be used with a filter monitor for a 3000-gallon rating.

General Installation Instructions

1. These filter kits must be installed in compliance with all state and local laws and regulations governing the installation and use of this product. Maximum inlet water temperature 100°F (38°C).

2. Mount the filter head in a suitable location, using the filter mounting bracket and screws supplied. Allow enough room under the filter head for installation and removal of the filter cartridge (13″ minimum).

3. Connect the cold water supply to the filter through a shut-off valve and 3/8″ O.D. tubing (supplied by the installer). For ease of servicing, the shut-off valve should be located within easy reach of the filter.
   NOTE: The inlet and outlet fitting supplied as part of the filter head are John Guest Superseal fittings that accept 3/8″ O.D. tubing on the filter inlet and 1/4″ O.D. tubing on the outlet. They may be used with copper, semirigid nylon or
   polypropylene tubing, with a rated working pressure equal to or greater than encountered in the application. Do not use soft or braided tubing.

4. CAUTION: If supply pressure will ever exceed 100 psi, install a pressure regulator to limit the inlet pressure to the filter to 100 psi or below.
   DO NOT ATTACH THE HOT WATER LINE TO THE FILTER.
   To make connections on the filter head, loosen the locknut. Push the tube end past both o-rings to a positive stop in the filter head recess – approx. 1″, locknut may have to be backed out a little more. Screw the locknut hand tight to seal (See Fig. 1). Ends of tubing must be cut square and free of burrs and sharp ends that could cut or nick the o-rings.

5. Connect the outlet of the filter to the inlet of the union using the 1/4″ O.D. poly tubing and 1/4″ union supplied.

6. Remove the filter from the carton, remove the protective cap, and attach the filter to the filter head by firmly inserting it into the head and rotating the filter clockwise.
   OPERATION OF QUICK CONNECT FITTINGS

7. Universal Bottle Filler and Water Cooler

   • Turn on the water supply and hold open the bubbler on the cooler until approximately 1 gallon of water is dispensed.
   • This flushing procedure purges air and fine carbon particles from the filter.
   • When 1 gallon of water has been purged through the cooler, carefully inspect all water connections for leaks.

8. Wall Bottle Filler

   • Turn on the water supply and activate the electric eye on the In-Wall Bottle Filler until approximately 1 gallon of water is dispensed.
   • Please note that the electric eye activation times out at 30 seconds and will need to be activated repeatedly until one gallon has been passed.
   • This flushing procedure purges air and fine carbon particles from the filter.
   • When 1 gallon of water has been purged through the bottle filler, carefully inspect all water connections for leaks.

Filter Replacement

1. Turn the inlet water valve off.
2. Open the bubbler or activate the electric eye to relieve pressure build-up in the system.
3. Remove the used filter from the head by rotating the filter counterclockwise.
4. Remove the new filter from the carton, and remove the protective cap; the cap may be placed on an old filter to reduce the chance of water spilling from the filter housing.
5. Attach the filter to the filter head by firmly inserting it into the head and rotating the filter clockwise.
   NOTE : The filter head contains an automatic shut-off valve that stops the flow of water if the filter is removed inadvertently without shutting off the incoming water.

Wall Bottle Filler

• Turn on the water supply and activate the electric eye on the In-Wall Bottle Filler until approximately 1 gallon of water is dispensed.
• Please note that the electric eye activation times out at 30 seconds and will need to be activated repeatedly until one gallon has been passed.
• This flushing procedure purges air and fine carbon particles from the filter. When 1 gallon of water has been purged through the bottle filler, carefully inspect all water connections for leaks.

FILTER KIT

EWF3000 Kit
(Lead, Chlorine, Taste & Odor, and Particulate Class I Reduction)

FOR COMMERCIAL USE ONLY
NOTE: This system and installation shall comply with applicable state and local regulations.
NOTE: Performance will vary depending on local water conditions.
Note: Brackets can be turned over to provide a better fit in some models.

NOTICE
To receive maximum benefit from your Genuine ELKAY® filters, note the installation dates below and change them according to the following guidelines.

REPLACEMENT FILTER OPTIONS
ELKAY Part No. 51300C — Lead Reduction Filter Change every 3,000 gallons as indicated by the filter monitor, or once a year – whichever occurs first. Scan for troubleshooting and sign up for auto replenishment of authentic Elkay filters.

KEEP THIS SHEET IN A HANDY LOCATION

FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.834.4816
ELKAY MANUFACTURING COMPANY 1333 BUTTERFIELD ROAD, SUITE 200 DOWNERS GROVE, IL 60515 630.574.8484 www.elkay.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>