Infinity HARMAN KAPPA 6 Marine Speaker Owner’s Manual
- June 6, 2024
- Infinity HARMAN
Table of Contents
- THANK YOU FOR YOUR PURCHASE
- ABOUT THE MANUAL
- WHAT’S IN THE BOX
- DIMENSIONS
- SPEAKER SIGNAL WIRING
- SPEAKER LED WIRING
- APPLYING FOAM SEAL
- MOUNTING THE SPEAKER
- REMOVING THE TWEETER FOR SEPARATE MOUNTING (KAPPA 8 ONLY)
- FLUSH-MOUNTING THE TWEETER
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
INFINITY KAPPA 6, KAPPA 8, AND
KAPPA 10 MARINE SPEAKER
Owner’s Manual
THANK YOU FOR YOUR PURCHASE
Your Infinity product has been designed to provide you with the performance and ease of operation you would expect from Infinity.
ABOUT THE MANUAL
This manual describes general installation guidelines. However, please note that proper installation of marine audio components requires qualified experience. If you do not have the knowledge and tools to successfully perform this installation, we strongly recommend consulting an authorized Infinity dealer about your installation options. Keep all instructions and sales receipts for reference.
WHAT’S IN THE BOX
DIMENSIONS
SPEAKER SIGNAL WIRING
To send a signal to the infinity marine speaker, connect the positive (+) and negative (-) speaker wires to the appropriate speaker outputs of your source unit or amplifier. Be sure to observe proper polarity.
SPEAKER LED WIRING
To provide power for the LEDs, plug the 24-gauge black (+), blue, green, and red LED wires from the speaker into the included female connector, then run the wires from the female connector to your compatible 12-volt power source or light controller (sold separately). If using a separate controller, be sure to connect each wire to the proper output.
If
hardwiring the LEDs directly to your power source, you can choose the color of
the LEDs by connecting the black Me to the positive (+) terminal, and the
appropriate R, G, and/or B single wire or combination of wires to the negative
(-) terminal. There are 7 possible colors, depending on the wiring
configuration you choose:
Wire connected to positive (+12V) terminal| The wire connected to
the negative (-) terminal| Color produced
---|---|---
Black| Red| Red
Green| Green
Blue| Blue
Red + Green| Yellow
Red + Blue| Purple
Blue + Green| Aquamarine
Red + Blue + Green| White
APPLYING FOAM SEAL
To help seal your installation against water, and to provide an airtight acoustic seal, apply the self-adhesive foam seal to the speaker frame.
MOUNTING THE SPEAKER
Use the included screws to mount the speaker to the location. Use the included
speed dips if necessary to provide a secure mount.
NOTE. Use caution when cutting and using screws with fiberglass to
prevent scratches and cracks.
REMOVING THE TWEETER FOR SEPARATE MOUNTING (KAPPA 8 ONLY)
Use the included 2-pin tool to remove the tweeter from the woofer housing. Place the pins of the tool in the holes of the tweeter grille and rotate 45 degrees clockwise to loosen and remove.
FLUSH-MOUNTING THE TWEETER
Place the tweeter in the mounting bracket and use the tool to secure by turning 45 degrees counter-clockwise.
To
transmit the audio signal to the tweeter, make sure the woofer and tweeter are
connected with the included cable.
Place the tweeter in the mounting location, then turn each setscrew clockwise to tighten mounting brackets. Use caution so as not to overtighten. Snap the included outer ring over the mounting bracket to hide the setscrews.
| Specifications | Kappa 6 | Kappa 8 | Kappa 10 |
|---|---|---|---|
| Continuous power handling | 100W | 200W | 300W |
| Peak power handling | 300W | 500W | 900W |
| Frequency response | 40Hz – 25kHz | 30Hz – 22kHz | 20Hz – 2kHz |
| Nominal impedance | 3 Ohms’ | 3 Ohms* | 2 or 4 Ohms (use |
switch to select)
Sensitivity| 92dB| 92dB| 89dB
External diameter| 7-15/32″ (189.4mm)| 9-1/2″ (241mm)| 11-5/8″ (295mm)
Mounting cutout diameter| 5-23/32″ (144.8mm)| Woofer: 7 “
(177.4mm) Tweeter bracket: 4-9/16″ (115.9mm)| 9-9/16″ (235.6mm)
Total depth| 3-21/32″ (92.5mm)| 4-9/32″ (108.1mm)| 6-13/32″
(162.4mm)
Mounting depth| 2-9/16″ (65mm)| 3-3/16″ (80.5mm)| 4-7/8″ (123mm)
‘NOTE Because of the woofer’s low impedance, do not wire two or more in parallel to an amplifier; doing so can result in overheating and damage to the amplifier.
HARMAN International Industries, Incorporated 8500 Balboa Boulevard,
Northridge, CA 91329 USA
www.infinityspeakers.com
© 2018 HARMAN International Industries, Incorporated. M rights reserved.
Infinity’s a trademark of HARMAN International Industries, Incorporated,
registered in the United States and/or other countries. Features,
specifications, and appearance we subject to change without notice.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>