rutec CYRA S Eco Refit LED Downlights Instruction Manual

rutec CYRA S Eco Refit LED Downlights

ELECTROTECHNICAL SAFETY INSTRUCTIONS:

Have the installation carried out by a qualified electrician. Any liability claim for spotlights that have not been installed in accordance with the European safety directives is void.

Attention

Connect CYRA Eco LED-Downlights only to a suitable LED converter. Only use flexible low-voltage cable for all connections on the secondary side of the converter.

INSTALLATION & SAFETY INSTRUCTIONS

Risk of electric shock:

Before installing or changing the downlight, disconnect the voltage. Ensure that the voltage cannot be switched on again accidentally.

• Make the hole (if not already present) according to the technical drawing.
• Can be installed in concrete pots.

MARKS AND SYMBOLS

Control gear & CYRA:

 CE-compliant with the applicable European directives.
 RoHS mark for products that do not contain heavy metals (2011/65/EU)
 REACH mark for products whose chemical components are known, registered and authorised. (1907/2006/EC)

Operating device:

 Protection class II:
double or reinforced insulated housing
 Do not cover the LED luminaire or control gear with heat-insulating materials.
 Parallel connection:
Suitable for through-wiring

DISPOSAL

 Dispose of electrical and electronic equipment in an environmentally sound manner. For more information, contact your local authority

TECHNICAL DATA

LED converter:

Input:
198-264 V AC; 180-280 V DC
AC 50 / 60 Hz

Ambient temperature:

-20 to +45° C

Pno:
≤ 0,5 W
Efficiency at full load:
≥ 88%
Tolerance:
± 5%

CYRA Eco LED-Downlights:

Power- / current consumption:

Colour rendering:
CRI 80, 3SDCM

Glare Rating:
UGR: <19
Beam angle:
60°

Installation depth :
80 mm

Lifetime:
L80B10: 50.000 h

Ecodesign:
This product contains a light source of energy efficiency class D.

CONVERTER PER CIRCUIT BREAKER:

| B10| B16| B20| C10| C16| C20
---|---|---|---|---|---|---
7-14 W

On/Off

| 29 pcs| 46 pcs| 57 pcs| 46 pcs| 73 pcs| 91 pcs
7-14 W DALI| 16 pcs| 26 pcs| 33 pcs| 26 pcs| 42 pcs| 53 pcs
18-24W

On/Off

| 29 pcs| 46 pcs| 57 pcs| 46 pcs| 73 pcs| 91 pcs
18-24 W DALI| 39 pcs| 63 pcs| 78 pcs| 39 pcs| 63 pcs| 78 pcs

TECHNICAL DRAWING

• CYRA S Eco:
  

• CYRA M Eco
  

• CYRA L Eco:
  

• CYRA XL Eco:
  

• LED CONVERTER:
  

 DIP-SWITCH SELECTION FOR POWER SETTING:

CC23W150-500 DALI; CC23W150-500:

Power | Current| Pin 1| Pin 2| Pin 3
---|---|---|---
7 W | 200 mA| Off| Off| On
9 W | 250 mA| Off| On| Off
14 W | 400 mA| On| Off| On

CC30W350-700 DALI:

Power | Current| Pin 1| Pin 2| Pin 3
---|---|---|---
18 W | 500 mA| Off| On| On
24 W | 700 mA| On| On| On

CC30W350-700:

Power | Current| Pin 1| Pin 2| Pin 3
---|---|---|---
18 W | 500 mA| On| On| Off
24 W | 700 mA| On| On| On

WIRING DIAGRAM

MOUNTING INSTRUCTION

1. If not already present, cut out the ceiling according to the technical drawing of the corresponding CYRA Eco model. Lay the cable according to detail 1 or 2, observing the polarity.
   

2. Set the desired power of the CYRA Eco LED-downlight according to the „DIP-SWITCH“ table using the 3 dip switches
   

3. Insert the LED control gear through the ceiling cut-out into the installation room.
   

4. Insert the CYRA Eco LED-downlight with tensioned springs into the ceiling cut-out until the downlight is seated with the stop angles in the cut-out and rests against the centring springs. Then press the LED downlight lightly into the ceiling cut-out. The bevelled centring springs position the downlight centrally in the ceiling cut-out.
   

5. The tension springs must be in a horizontal position after installation, not vertical. If the downlight is correct position, the springs fold back and the CYRA Eco LED-downlight pulls itself against the ceiling cut-out.
   

CUSTOMER SUPPORT

Carl-Zeiss-Str. 15 D – 28857 Syke www.rutec.de

References

• Products - rutec Licht (EN)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>