rutec 80699 DALI-2 DT6 NFC Push Dimming Actuator Instruction Manual

rutec 80699 DALI-2 DT6 NFC Push Dimming Actuator

Specifications

• Input: 200 – 240 V AC, 50/60 Hz, 200-240 V DC
• Output: 6-42 V DC, 0.6-15 W
• Standby Power: 0.5 W
• Efficiency at full load: 89%
• Dimensions (L x W x H): 135 x 35 x 20 mm

Product Information
The DALI-2 NFC Push dimming actuator 80699 is a Dali or Push dimmable actuator which provides a rectified constant current of 100-700 mA and a maximum power of 45 W on the secondary side. The] output current is adjustable in 0.1 mA steps via NFC. Instructions] for the setting are available at: www.rutec.de.

Installation

To install the actuator, follow these steps:

1. Ensure the power is turned off before starting the installation.
2. Connect the wiring according to the provided wiring diagrams for either Push-Dim or DALI-Dim.
3. Use a flexible cable with a maximum connection length of 8.0 m for the secondary side.

Usage Instructions

To use the DALI-2 NFC Push dimming actuator:

1. Ensure the power supply is within the specified input range.
2. Adjust the output current using NFC in 0.1 mA steps as needed.
3. Refer to the user manual for specific operations with a DALI master controller.

FAQ:

Q: What should I do if the product does not respond to NFC adjustments?|
A: Make sure that the NFC function is enabled on your device andthat you are following the correct steps for adjusting the output current. If issues persist, refer to the troubleshooting section in the user manual or contact customer support for assistance.

SAFETY INSTRUCTIONS

General notes for installation

• Commission a qualified electrician to carry out the installation.
• Always ensure that the unit is installed in a location with good ventilation to ensure the correct operating temperature.
• Never connect the cables when the unit is switched on.
• Check the correctness of the connections and check for short circuits before switching on the voltage.
• Please do not carry out any repairs yourself. This will invalidate the manufacturer‘s warranty.

FOR THE INSTALLATION SITE AND

THE PRODUCT MUST BE TAKE

INTO ACCOUNT
The product is only suitable for dry indoor use.
The permissible ambient temperature for the product is -20 to + 45° C.
Improper use will destroy the product and we will not accept any guarantee. Therefore, please observe our assembly instructions.

TOOLS REQUIRED
The following tools are required for mounting the LED actuator:

• Drilling machine with various stone and HSS drills
• Cordless screwdriver with various bit sets
• Screws, dowels
• Hammer, screwdriver etc.

DISPOSAL

Dispose of electrical and electronic equipment in an environmentally sound manner. For more information, contact your local authority.

TECHNICAL DATA:

Input:
200 – 240 V AC, 50/60 Hz, 200-240 V DC

Output:
6-42 V DC, 0.6-15 W

Ambient temperature:
-20 to +45° C

Psb:
0.3 W

Pno:
1.0 W

Efficiency at full load:
89 %

Tolerance:
± 3 %

Operation with Dali master
1 DALI address for 1 channel output are assigned by DALI Master controller automatically, please refer to user manuals of compatible DALI Masters for specific operations.

TECHNICAL PRODUCT

DIMENSIONS:
Dimensions (L x W x H): 135 x 35 x 20 mm

POWER SUPPLY UNITS PER CIRCUIT BREAKER

WIRING DIAGRAM WITH PUSH-DIM

WIRING DIAGRAM WITH DALI-DIM

The DALI-2 NFC Push dimming actuator 80699 is a Dali or Push dimmable actuator which provides a rectified constant current of 100-700 mA and a maximum power of 45 W on the secondary side. The output current is adjustable in 0.1 mA steps via NFC Instructions for the setting are available at: www.rutec.de

INSTALLATION:

• First connect the LED-downlight to the secondary side of the actuator. Pay attention to the correct polarity + (anode) and – (cathode).
• Connect the primary side of the actuator to the 230 V AC mains voltage in a voltage-free state.
• Check that the input and output cables have been connected correctly before switching on the power to operate the actuator.

INSTALLATION NOTE:
We recommend a flexible cable with a maximum connection length of 8.0 m for the secondary side.

NFC FUNCTIONS
CUSTOMISE DEVICE SETTINGS VIA APP:
Please scan the following QR code to download the app instructions for the device settings.

References

• Products - rutec Licht (EN)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>