rutec Licht DALI-2 DT6 NFC Push Dimming Actuator Instruction Manual

May 15, 2024
rutec Licht

DALI-2 DT6 NFC push dimming actuator
80690
MOUNTING AND OPERATING INSTRUCTIONS

SAFETY INSTRUCTIONS:

General notes for installation

  • Commission a qualified electrician to carry out the installation.
  • Always ensure that the unit is installed in a location with good ventilation to ensure the correct operating temperature.
  • Never connect the cables when the unit is switched on.
  • Check the correctness of the connections and check for short circuits before switching on the voltage.
  • Please do not carry out any repairs yourself. This will invalidate the manufacturer‘s warranty.

FOR THE INSTALLATION SITE AND THE PRODUCT MUST BE TAKE INTO ACCOUNT:
The product is only suitable for dry indoor use.
The permissible ambient temperature for the product is -20 to + 45° C.
Improper use will destroy the product and we will not accept any guarantee. Therefore, please observe our assembly instructions.

TOOLS REQUIRED:

The following tools are required for mounting the LED actuator:

  • Drilling machine with various stone and HSS drills
  • Cordless screwdriver with various bit sets
  • Screws, dowels
  • Hammer, screwdriver etc.

DISPOSAL:

**** Dispose of electrical and electronic equipment in an environmentally sound manner. For more information, contact your local authority.

TECHNICAL DATA:

Input:
100 – 240 V AC, 50/60 Hz, 200-240 V DC
Output:
6-54 V DC, 3-45 W
Ambient temperature:
-20 to +45° C
Psb:
0.25 W
Pno:
1.0 W
Efficiency at full load:
89 %
Tolerance:
± 3 %

Operation with Dali master
1 DALI address for 1 channel output are assigned by DALI Master controller automatically, please refer to user manuals of compatible DALI Masters for specific operations.

TECHNICAL PRODUCT DIMENSIONS:

Dimensions (L x W x H):
145 x 45 x 30 mm

rutec Licht DALI-2 DT6 NFC Push Dimming Actuator -
DIMENSIONS

POWER SUPPLY UNITS PER CIRCUIT BREAKER:

CBR B10 B16 B25 C10 C16 C25
Pcs. 17 28 43 28 44 70

WIRING DIAGRAM WITH PUSH-DIM:

rutec Licht DALI-2 DT6 NFC Push Dimming Actuator -
DIAGRAM

WIRING DIAGRAM WITH DALI-DIM:

rutec Licht DALI-2 DT6 NFC Push Dimming Actuator - WIRING
DIAGRAM The DALI-2 NFC Push dimming actuator 80690 is a Dali or Push dimmable actuator which provides a rectified constant current of 500-1400 mA and a maximum power of 45 W on the secondary side. The output current is adjustable in 0.1 mA steps via NFC Instructions for the setting are available at: www.rutec.de

INSTALLATION:

  • First connect the LED-downlight to the secondary side of the actuator. Pay attention to the correct polarity + (anode) and – (cathode).
  • Connect the primary side of the actuator to the 230 V AC mains voltage in a voltage-free state.
  • Check that the input and output cables have been connected correctly before switching on the power to operate the actuator.

INSTALLATION NOTE:
We recommend a flexible cable with a maximum connection length of 8.0 m for the secondary side.
NOTES:rutec Licht DALI-2 DT6 NFC Push Dimming Actuator -
Symbol

Carl-Zeiss-Str. 15
28857 Syke
D ALI-2_NF C_Push_Dimm_Aktor_80690_B A_02/2024

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals