AURATON IP20 Heat Monitor Termostat Owner’s Manual
- June 13, 2024
- AURATON
Table of Contents
AURATON IP20 Heat Monitor Termostat
Product Information
- Product Name : AURATON Heat Monitor
- Version : 20200317
- Compatibility : Compatible with Auraton Radiator Heater Controller and Auraton Heater Controller
- Description : Wireless temperature controller
Product Usage Instructions
Battery Installation / Replacement
Battery sockets are located inside the controller on both sides of the
display. To install the batteries, follow the steps below
- Remove the controller enclosure as shown in the figure.
- Place two AAA 1.5 V batteries in the battery socket, observing the correct polarity.
- Note: We recommend using alkaline batteries to supply AURATON controllers. Rechargeable batteries should not be used because their rated voltage is too low.
Pairing Devices
To pair the Auraton Heat Monitor with another device, follow the steps
below
- On the Auraton Heat Monitor regulator, simultaneously press the “+” or “-” button for 3 seconds until the transmission symbol ( ) lights up on the display.
- The Auraton Heat Monitor controller will wait for 30 seconds to pair.
- Turn on the pairing mode on the second device you want to pair and wait for confirmation from the other device.
- After 30 seconds, the Auraton Heat Monitor will automatically return to normal operation.
Technical Specifications
- Temperature Range : Operating temperature range
- Measurement Range : Temperature measurement range
- Control Range : Temperature control range
- Hysteresis : Hysteresis value
- Additional Function : FrostGuard/Hotel Mode
- Operating Cycle : Daily cycle
- Work Status Control : LCD display
- Power Supply : 2 x LR03 (AAA) batteries
- Protection Class : IP20
- Radio Frequency : 868,150 MHz; 868,450 MHz; 869,800 MHz
- Radio Signal Power : 11 dBm
- Radio Receiver Category : 2
- Operating Range : Up to 30 m inside a building
Please refer to the official user manual for more detailed instructions and information.
Source: https://manuals.auraton.pl
Controller description
- Wireless temperature controller, which is compatible with
- Auraton Radiator Heater Controller and Auraton Heater Controller
The extended instruction can be found at
https://manuals.auraton.pl
Manufacturer
Selecting the proper location for temperature regulator
Regulator
- LCD display
- Temperature increase key
- Temporary temperature decrease mode keys
- Temperature decrease key
- Acknowledge or on/off key
Display
- Temperature
- Temperature unit
- Hotel mode ( )
- Day mode indicator ( )
- Night mode indicator ( )
- Indicator of controller activation ( )
- Low battery ( )
- Transmission symbol ( )
Battery installation / replacement
- Battery sockets are located inside the controller on both sides of the display. To install the batteries, remove the controller enclosure as shown in the figure.
- Place two AAA 1.5 V batteries in the battery socket observing the correct polarity.
- NOTE: We recommend using alkaline batteries to supply AURATON controllers. Rechargeable batteries should not be used because their rated voltage is too low.
Pairing devices
1. On the Auraton Heat Monitor regulator, simultaneously press the or button
for 3 seconds until the transmission symbol ( ) lights up on the display. The
Auraton Heat Monitor controller waits for 30 seconds to pair. After this time,
it will automatically return to normal operation.
2. Turn on the pairing mode on the second device you want
Technical specifications
Disposing of the devices
The devices are marked with the crossed waste bin symbol. According to
European Directive no. 2012/19/EU and the Act concerning used up electric and
electronic equipment, such a marking indicates that this equipment may not be
placed with other household generated waste.
The user is responsible for delivering the devices to a reception point for
used-up electric and electronic equipment Hereby, LARS Andrzej Szymański
declares that the radio equipment type Auraton Heat Monitor is in compliance
with Directive 2014/53/EU and 2011/65/EU. The full text of the EU declaration
of conformity is available at the following internet address
https://manuals.auraton.pl