rutec 85480-V2 24V 40-75 6W IP20 Dimmbar LED Power Supply 24V 40-75 6W IP20 Dimmable Instruction Manual
- June 1, 2024
- rutec
Table of Contents
LED power supply 24V,
40-75,6W IP20 dimmable
85480-V2
MOUNTING AND
OPERATING INSTRUCTIONS
SAFETY INSTRUCTIONS:
General notes for installation
- Commission a qualified electrician to carry out the installation.
- Always ensure that the unit is installed in a location with good ventilation to ensure the correct operating temperature.
- Never connect the cables when the unit is switched on.
- Check the correctness of the connections and check for short circuits before switching on the voltage.
- Please do not carry out any repairs yourself. This will invalidate the manufacturer‘s warranty.
FOR THE INSTALLATION SITE AND THE PRODUCT MUST BE TAKE INTO ACCOUNT:
The product is only suitable for dry indoor use.
The permissible ambient temperature for the product is -20 to + 40° C.
Improper use will destroy the product and we will not accept any guarantee.
Therefore, please observe our assembly instructions.
TOOLS REQUIRED:
The following tools are required for mounting the LED power supply unit:
- Drilling machine with various stone and HSS drills
- Cordless screwdriver with various bit sets
- Screws, dowels
- Hammer, screwdriver etc.
DISPOSAL:
Dispose of electrical and electronic equipment in an environmentally sound
manner. For more information, contact your local authority.
TECHNICAL DATA:
Input: 220 – 240 V AC, 50/60 Hz
Output: 24 V DC, 40-75.6 W
Ambient temperature: -20 to +40° C
Psb: 0.00
Pno: 0.42
Efficiency at full load: 88.5 %
Tolerance: ± 5 %
TECHNICAL PRODUCT DIMENSIONS:
Length x width x height ( L x W x H ) 204 x 53.5 x 30 mm
POWER SUPPLY UNITS PER CIRCUIT BREAKER:
CBR | B10 | B16 | B25 | C10 | C16 | C25 |
---|---|---|---|---|---|---|
Pcs. | 2 | 3 | 5 | 3 | 5 | 8 |
The LED power supply unit 85480-V2 is a triac-dimmable power supply unit on the primary side, which provides a rectified constant voltage of 24 V DC and a power of 40-75,6 W on the secondary side.
WIRING DIAGRAM:
INSTALLATION
- First connect the LED strip to the secondary side of the power supply unit. Pay attention to the correct polarity + (anode) and – (cathode).
- Connect the primary side of the LED power supply unit to the 230 V AC mains voltage or a suitable triac dimmer in a voltage-free state.
- Check that the input and output cables have been connected correctly before switching on the power to operate the LED power supply.
INSTALLATION NOTE:
We recommend a flexible cable with a maximum connection length of 4.0 m for
the secondary side.
NOTES:————-
LED-N e tz gerät 40-75,
6W_85480- V2_MA_09/2023
Documents / Resources
|
rutec 85480-V2 24V 40-75 6W IP20 Dimmbar LED Power Supply 24V 40-75 6W IP20
Dimmable
[pdf] Instruction Manual
85480-V2 24V 40-75 6W IP20 Dimmbar LED Power Supply 24V 40-75 6W IP20
Dimmable, 85480-V2, 24V 40-75 6W IP20 Dimmbar LED Power Supply 24V 40-75 6W
IP20 Dimmable, Dimmbar LED Power Supply 24V 40-75 6W IP20 Dimmable, LED Power
Supply 24V 40-75 6W IP20 Dimmable, 24V 40-75 6W IP20 Dimmable, 6W IP20
Dimmable, IP20 Dimmable, Dimmable
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>