binardat CPE300 Outdoor Wireless Bridge User Manual

binardat CPE300 Outdoor Wireless Bridge

Hardware connection schematic diagram

Interface Descriptions

• DIP Switch: To adjust the transformation between the main AP mode and the secondary AP mode of the bridge.
• DC: Power interface,12V 1A DC power interface.
• Digital Switch/Reset: Both the digital switch and reset button, short press the button when electrifying, and the numeric value of the digital tube will be added once pressed 15 seconds, the device will be restored to the factory setting.

2.4G Bridge

• LAN1/POE: This is a data transmission port, and it is also a power port.
• When the device works in the bridge mode, the interface acts as a LAN port function. When the device works in the route mode, the interface acts as a WAN port function. This interface is used to connect the POE interface to the POE power.
• LAN2: This is a LAN data transmission port that can connect computers, cameras, switches, and other devices.

5.8G Bridge

• ETH/ POE interface: This is a data transmission port, and it is also a power port. When the device works in the bridge mode, the interface acts as a LAN port function. When the device works in the route mode, the interface acts as a WAN port function. This interface is used to connect the POE interface to the POE power.
• COM: It is a debugging interface.

Indicator light state description

2.4G Bridge

The fast pairing of digital switch

One-to-one pairing method

1. Dial a bridge to “M” and another bridge to “S”.
2. Short press the “Dig SW/ Reset” button, each digital tube value will add one (0-9-A-F cycle).
3. The paired bridge is set to the same value and can be paired successfully.

One to multiple pairing method

1. Dial a bridge to “M” and the other bridge to “S”.
2. Short press “Dig SW/ Reset” button, each digital tube value will add one (0-9-A-F cycle).
3. The paired bridge is set to the same value and can be paired successfully.

Digital tube and wireless channel comparison table

2.4G Bridge

5.8G Bridge

Note

1. The default channel bandwidth of the wireless bridge is 40MHz;
2. The number of channels supported by some wireless bridges will vary. Please refer to the actual product.

Setting up a bridge in a browser Computer settings

1. Open the computer–Right-click [Internet] – [Attribute] – [Change adapter settings].
2. Right-click of the mouse click [Local connection], and Select [Attribute]
3. Double-click the [Internet Protocol version 4 (TCP/IPv4)] in the connection properties dialog box project(as shown in the left below).
4. In the [Internet protocol version 4] dialog box, choose [use the following IP address] and set the IP address to 169.254.254.X (X is any number between 1-253), and the subnet mask is set to 255.0.0.0 (as shown in the right below). Finally, click [OK] and quit.

Login management interface

The default mode of the device is the bridge mode, open the computer browsers, after entering its address 169.254.254.254, the bridge device list will be displayed, and clicks on the [login] button to log in to the device.
Note: Some wireless bridges do not have a “Bridge Device list” function. Please refer to the actual product for details.

• The username and password of the web management platform are all admin, click the [login] button to log in to the device.

Network settings

• Configuring the mode and bridge interface according to the network usage of the site. [Bridge mod] refers to the wireless transmission of data by the device. [Route mode] refers to the device’s NAT conversion and wireless transmission of the data.

Description: The device supports bridge mode and route mode in the“M” AP mode, but only supports the bridge mode in the “S” AP mode.

Wifi settings

• Note: Some wireless bridges do not have this function. Please refer to the actual product for details.
• The default WiFi name of the 2.4G Bridge is Brap-2G-XXXX, the password is 88888888.
• The default WiFi name of the 5.8G Bridge is Brap-5G-XXXX the password is 88888888.
• Computers, mobile phones, and other terminals can be wirelessly connected to the device through this signal. Remarks XXXX is the last four bits of the bridge’s MAC address x

Description: The device launches the WiFi signal in the main AP mode. In the secondary AP mode, the WiFi signal is transmitted only after the bridge pairing is successfully connected. Bound cloud end
Note: Some wireless bridges do not have this function. Please refer to the actual product for details.
If the device is connected to the Internet, you can configure the 【bridge interface】 information. After the device is connected to the Internet, it can be remotely managed by the cloud.

1. Login to “www.tianwifi.net” to apply for a cloud account.
2. Fill in your cloud account in the “username” column.
3. The server address bar is filled in “www.tianwifi.net”
4. The device description bar suggests filling up the installation location for later management.

Click the 【Save】 button, prompting the ‘connection state: Connected to www.tianwifi.net’, which indicates that the device has successfully bound the cloud

Wuhan niannianxingchen Technology Co., Ltd.

• No. 349 Guanshan Road, Gaoxin Avenue, Wuhan, Hubei, China
• support@binardat.com.
• www.binardat.com.

References

• Binardat Store

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>