rutec DALI-2 DT6 NFC Push Dimming Actuator User Manual
- June 1, 2024
- rutec
Table of Contents
DALI-2 DT6 NFC push dimming actuator
80690
MOUNTING AND OPERATING INSTRUCTIONS
SAFETY INSTRUCTIONS:
General notes for installation
- Commission a qualified electrician to carry out the installation.
- Always ensure that the unit is installed in a location with good ventilation to ensure the correct operating temperature.
- Never connect the cables when the unit is switched on.
- Check the correctness of the connections and check for short circuits before switching on the voltage.
- Please do not carry out any repairs yourself. This will invalidate the manufacturer‘s warranty.
FOR THE INSTALLATION SITE AND THE PRODUCT MUST BE TAKE INTO ACCOUNT:
The product is only suitable for dry indoor use.
The permissible ambient temperature for the product is-20 to + 45° C.
Improper use will destroy the product and we will noaccept any guarantee.
Therefore, please observe our assembly instructions.
TOOLS REQUIRED:
The following tools are required for mounting the LED actuator:
- Drilling machine with various stone and HSS drills
- Cordless screwdriver with various bit sets
- Screws, dowels
- Hammer, screwdriver etc.
DISPOSAL:
**** Dispose of electrical and electronic equipment in an environmentally
sound manner. For more information, contact your local authority.
TECHNICAL DATA:
Input: 100 – 240 V AC, 50/60 Hz, 200-240 V DC
Output: 6-54 V DC, 3-45 W
Ambient temperature: -20 to +45° C
Psb: 0.25 W
Pno: 1.0 W
Efficiency at full load: 89 %
Tolerance: ± 3 %
Operation with Dali master
1 DALI address for 1 channel output are assigned by DALI Master controller
automatically, please refer to user manuals of compatible DALI Masters for
specific operations.
TECHNICAL PRODUCT DIMENSIONS:
Dimensions (L x W x H):
145 x 45 x 30 mm
POWER SUPPLY UNITS PER CIRCUIT BREAKER:
CBR | B10 | B16 | B25 | C10 | C16 | C25 |
---|---|---|---|---|---|---|
Pcs. | 17 | 28 | 43 | 28 | 44 | 70 |
WIRING DIAGRAM WITH PUSH-DIM:
WIRING DIAGRAM WITH DALI-DIM:
The DALI-2 NFC Push dimming actuator 80690 is a Dali or Push dimmable actuator which provides a rectified constant current of 500-1400 mA and a maximum power of 45 W on the secondary side. The output current is adjustable in 0.1 mA steps via NFC Instructions for the setting are available at: www.rutec.de
INSTALLATION:
- First connect the LED-downlight to the secondary side of the actuator. Pay attention to the correct polarity + (anode) and – (cathode).
- Connect the primary side of the actuator to the 230 V AC mains voltage in a voltage-free state.
- Check that the input and output cables have been connected correctly before switching on the power to operate the actuator.
INSTALLATION NOTE:
We recommend a flexible cable with a maximum connection length of 8.0 m for
the secondary side.
NOTES:………………….
NFC FUNCTIONS:
CUSTOMISE DEVICE SETTINGS VIA APP:
Please scan the following QR code to download the app instructions for the
device settings.
D ALI-2_NF C_Push_Dimm_Aktor_80690_B A_03/2024
Documents / Resources
|
rutec DALI-2 DT6 NFC Push Dimming
Actuator
[pdf] User Manual
80690, DALI-2 DT6 NFC Push Dimming Actuator, DALI-2, DT6 NFC Push Dimming
Actuator, NFC Push Dimming Actuator, Push Dimming Actuator, Dimming Actuator,
Actuator
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>