Z-Lite 428SF-OB Annora 15 Inch 3-Light Olde Bronze Semi Flush Mount Installation Guide

Z-Lite 428SF-OB Annora 15 Inch 3-Light Olde Bronze Semi Flush Mount

Product Information

Specifications

• Model : 428SF-BN, 428SF-OB
• Fixture Type : Ceiling Fixture
• Color : Brushed Nickel (BN), Oil Rubbed Bronze (OB)

Product Usage Instructions

Installation and Safety Instructions

• For Your Safety: Before starting the installation, ensure that the electricity to the wires you are working on is shut off. Either remove the fuse or shut off the circuit breaker.
• General: This fixture can be installed without any special tools. Follow the steps in the given order. Do not hang the fixture on house electrical wires or install it on a ceiling that contains a radiant type heating system. If you are unsure about the installation process, consult a qualified electrician. Proper wiring is essential for safe operation.

Fixture Assembly
Carefully remove the fixture from the carton and check that all parts are included as shown in the figure. Ensure that you do not misplace any screws or parts needed for installation.

Step 1: Thread pipe (F) into nipple (G).

Installation

Important: Do not attach the fixture directly to the outlet box.

1. Step 1: Thread mounting screws (A) into the mounting bar (B).
2. Step 2: Secure the mounting bar (B) to the outlet box using outlet box screws (C).

Grounding Instructions

Step 1: Insert the green grounding screw into the hole with two raised dimples on the mounting bar. Wrap the ground wire from the fixture (if supplied) around the green grounding screw, then connect it to the ground wire from the outlet box using a wire connector (not supplied). If the ground wire from the fixture is not supplied, wrap the ground wire from the outlet box around the green grounding screw and tighten it. Never connect the ground wire to black or white power supply wires.

Step 2: Take note of the color of the wires on your fixture. Identify which group your fixture wires fall into and connect them according to the directions below

• Group A: Connect to Black House Wire
• Group B: Connect to White House Wire

Refer to the provided table for wire color coding details.

Final Assembly

1. Step 1: After connecting the wires, carefully tuck them inside the outlet box. Raise the canopy (D) to allow the mounting screws (A) to protrude through the hole on the canopy.
2. Step 2: Secure the canopy using ball nuts (E).
3. Step 3: Place glasses (I), check ring (J), and over socket (H), then use wrench (L) to secure them with the retaining ring (K).
4. Step 4: Install a light bulb, making sure not to exceed the maximum capacity recommended for the socket.

Cleaning
To clean the fixture, wipe it with a soft cloth. Clean glass components with a mild soap. Do not use abrasive materials such as scouring pads, powders, steel wool, or abrasive paper.

Ordering Parts
Keep this sheet for future reference and in case you need to order replacement parts. When ordering parts, use the exact wording from the illustration. Note that the line art shown may not exactly match the enclosed fixture, but the installation instructions apply to this fixture.

FAQ (Frequently Asked Questions)

• Q: Do I need any special tools to install this fixture?
  A: No, you do not need any special tools to install this fixture.

• Q: Can I hang the fixture on house electrical wires?
  A: No, you should not hang the fixture on house electrical wires. Follow the provided installation instructions.

• Q: Can I install a swag type fixture on a ceiling with a radiant type heating system?
  A: No, you should not install a swag type fixture on a ceiling that contains a radiant type heating system.

• Q: What should I do if I am unsure about the installation process?
  A: If you are unsure about the installation process, consult a qualified electrician for assistance.

• Q: How should I clean the fixture?
  A: To clean the fixture, wipe it with a soft cloth. Clean glass components with a mild soap. Do not use abrasive materials.

INSTALLATION AND SAFETY INSTRUCTIONS

FOR YOUR SAFETY

WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE IS REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF.

GENERAL
You don’t need special tools to install this fixture. Be sure to follow the steps in the order given. Under no circumstances should a fixture be hung on house electrical wires, nor should a swag type fixture be installed on a ceiling which contains a radiant type heating system. Read instructions carefully. If you are unclear as to how to proceed, consult a qualified electrician. NOTE: Proper wiring is essential for the safe operation of this fixture.

FIXTURE ASSEMBLY
Carefully remove the fixture from the carton and check that all parts are included as shown in figure. Be careful not to misplace any of the screws or parts, which are needed to install this fixture.

STEP 1: Thread pipe (F) into nipple (G).

INSTALLATION

IMPORTANT: Do not attach fixture directly to outlet box.

1. STEP 1 : Thread mounting screws (A) into the mounting bar (B).
2. STEP 2 : Secure mounting bar (B) to outlet box with outlet box screws (C).

GROUNDING INSTRUCTIONS

1. STEP 1 : Insert the green grounding screw into the hole with two raised dimples on the mounting bar. Wrap the ground wire from the fixture (if supplied) around the green grounding screw, then connect it to ground wire from the outlet box (if not fixed on the outlet box) using a wire connector (not supplied). If ground wire from the fixture is not supplied, wrap the ground wire (if not fixed on the outlet box) from the outlet box around the green grounding screw and tighten it.
   NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES.

2. STEP 2 : Take note of the color of the wire(s) on your fixture. Identify which group your fixture wire(s) falls into and connect the wires according to the directions below: *NOTE : When parallel wire (SPT-I & SPT-2) is used, the tracer wire is square shaped or ridged and the less tracer wire is round in shape or smooth (seen best when viewed from wire end.)

3. STEP 3 : Take your fixture wire(s) from group A and place evenly against the black wire from the outlet box. Do NOT twist wires together before using wire connectors.

4. STEP 4 : Fit a wire connector (not supplied) over the wires and screw the connector clockwise until you feel firmness.

5. STEP 5 : Try gently to pull the connector off the wires. If you can pull the connector off, carefully re-do steps 3 and 4 as above, and check again for a firm connection.

6. STEP 6 : Connect the fixture wire from group B to the white wire from the outlet box in the same manner. Make sure no bare wires can be seen outside wire connectors.

FINAL ASSEMBLY

1. STEP 1 : After wires are connected, tuck them carefully inside outlet box. Raise canopy (D) allowing for the mounting screws (A) to protrude through the hole on canopy (D), then secure with ball nuts (E).
2. STEP 2 : Place glasses (I) ,check ring(J) and over socket (H) and use wrench (L) secure with retaining ring (K).
3. STEP 3 : Install light bulb. (Please do not exceed the maximum  capacity recommended on the socket.)

CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

ORDERING PARTS
Keep this sheet for future reference, and in case you need to order replacement parts. Be sure to use exact wording from illustration when ordering parts.

Line art shown may not exactly match the fixture enclosed. However, the installations do apply to this fixture.

• ITEM NO: 428SF-BN 428SF-OB

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>