Z-Lite 455-8L Chrome Linear Pendant Light Clear Glass Instruction Manual
- June 15, 2024
- Z-Lite
Table of Contents
Z-Lite 455-8L Chrome Linear Pendant Light Clear Glass
FOR YOUR SAFETY WARNING BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE IS REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF.
GENERAL
You don’t need special tools to install this fixture. Be sure to follow the
steps in the order given. Under no circumstances should a fixture be hung on
house electrical wires, nor should a swag-type fixture be installed on a
ceiling that contains a radiant-type heating system. Read instructions
carefully. If you are unclear as to how to proceed, consult a qualified
electrician.
NOTE: Proper wiring is essential for the safe operation of this fixture.
You don’t need special tools to install this fixture. Be sure to follow the
steps in the order given. Under no circumstances should a fixture be hung on
house electrical wires, nor should a swag-type fixture be installed on a
ceiling that contains a radiant-type heating system. Read instructions
carefully. If you are unclear as to how to proceed, consult a qualified
electrician.
NOTE: Proper wiring is essential for the safe operation of this fixture.
FIXTURE ASSEMBLY
Carefully remove the fixture from the carton and check that all parts are
included as shown in the figure. Be careful not to misplace any of the screws
or parts, which are needed to install this fixture.
STEP 1: Thread pipe (N) into nipple (O), pipe (M) into pipe (N), pipe (L)
into pipe (M), pipe (K) into pipe (L), pipe (J) into pipe (K), pipe (I) into
pipe (J), pipe (H) into pipe (I), and thread the swivel (G) into pipe (H),
then secure with
wing nut (F).
INSTALLATION
IMPORTANT: Do not attach the fixture directly to the outlet box.
STEP 1: Thread mounting screws (A) into the matching holes of the
Circular strap (B).
STEP 2: Secure circular strap (B) to outlet box with outlet box screws
(C).
GROUNDING INSTRUCTIONS
STEP 1: Insert the green grounding screw into the hole with two raised dimples on the mounting bar. Wrap the ground wire from the fixture (if supplied) around the green grounding screw, then connect it to the ground wire from the outlet box (if not fixed on the outlet box) using a wire connector (not supplied). If the ground wire from the fixture is not supplied, wrap the ground wire (if not fixed on the outlet box) from the outlet box around the green grounding screw and tighten it.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES.
STEP 2: Take note of the colour of the wire(s) on your fixture. Identify
which group your fixture wire(s) falls into and connect the wires according to
the directions below.
NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer wire is
square shaped or ridged and the less tracer wire is round in shape or smooth
(seen best when viewed from the wire end.)
STEP 3: Take your fixture wire(s) from group A and place it evenly
against the black wire from the outlet box. Do NOT twist wires together before
using wire connectors.
STEP 4: Fit a wire connector (not supplied) over the wires and screw the
connector clockwise until you feel firmness.
STEP 5: Try gently to pull the connector off the wires. If you can pull
the connector off, carefully re-do steps 3 and 4 as above, and check again for
a firm connection.
STEP 6: Connect the fixture wire from group B to the white wire from the
outlet box in the same manner. Make sure no bare wires can be seen outside
wire connectors.
FINAL ASSEMBLY
STEP 1: After the wires are connected, tuck them carefully inside the
outlet box. Raise canopy (D) allowing for the mounting screws (A) to protrude
through the holes on canopy (D), then secure with ball nuts (E).
STEP 2: Place the glass (Q) over the socket (P), then secure it with the
socket ring (R).
STEP 3: Install a light bulb. (Please do not exceed the maximum capacity
recommended on the socket.)
CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Be sure to use exact wording from illustrations when
ordering parts. The line art shown may not exactly match the fixture enclosed.
However, the installations do apply to this fixture. ITEM NO: 455-6L-CH 455
-8L-CH 455-10L-CH
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>