SIM-LAB GT1-PRO Cockpit Instruction Manual

: June 14, 2024
: SIM-LAB

Table of Contents

SIM-LAB GT1-PRO Cockpit Instruction
BEFORE YOU START
Tools needed
Assembly
Documents / Resources

SIM-LAB GT1-PRO Cockpit Instruction

BEFORE YOU START

Thank you for purchasing this Sim-Lab product! On the following pages, you will find detailed instructions on assembly. This requires only a set of simple tools and some of your time. Please check the bill of materials before starting (page 18) and make sure all the parts are delivered.
For the angled profiles, the lengths in the bill of materials might not perfectly match the length of the part you measure. Don’t worry, we measure differently when cutting the profiles and with the angles as they are, the given dimensions are a close approximation.
We tried to go with a different style of assembly for this one. Don’t panic if you can’t find any corner brackets included in the hardware bags.

Inserting Slot-Nuts:
You got excited, finished the build, put the caps on, but forgot to install one element. Do not worry. It happens to everyone. In this diagram, you can see how to insert a Slot-Nut directly into the slot from the side. You can also use one of your smaller Hex wrenches to help wiggle the Slot-Nut in place.

Tools needed

Note : the counterbores should point (arrows) to the outside of the cockpit. This page is showing assembly for the LEFT side.

Assembly

SIM-LAB-GT1--Cockpit-Instruction-image-3

SIM-LAB-GT1--Cockpit-Instruction-image-4

Part A12 is only countersunk on one side, therefore only fits on the LEFT side of the cockpit. For the RIGHT side of the upright assembly, see the next page.

SIM-LAB-GT1--Cockpit-Instruction-image-6

SIM-LAB-GT1--Cockpit-Instruction-image-8

SIM-LAB-GT1--Cockpit-Instruction-image-10

Part A15 is symmetrical and can be used on both sides of the cockpit.

SIM-LAB-GT1--Cockpit-Instruction-image-16

BOX A – GT1-Pro PROFILE KIT

#| Part| QTY| Note
A1| 80X40 Length=1350mm| 2| Machined.
A2| 80X40 Length=750mm| 2| Angled, with logo.
A3| 80X40 Length=560mm| 1| Angled.
A4| 80X40 Length=500mm| 2|
A5| 80X40 Length=430mm| 1| Angled.
A6| 40X40 Length=500mm| 2| Machined.
A7| 40X40 Length=400mm| 2|
HARDWARE KIT
A8| Pedal deck upright left| 1|
A9| Pedal deck upright right| 1|
A10| Pedal deck pivot| 2|
A11| Pedal deck| 1|
A12| Sandwich plate left| 1|
A13| Sandwich plate right| 1|
A14| Wheel deck| 1|
A15| Side mount sandwich plate| 1|
A16| Side mount plate| 2|
A17| Rubber foot| 4|
A18| Profile 80×40 end-cap| 4|
A19| Profile 80×40 end-cap angled| 6|
A20| Profile 40×40 end-cap| 8|
#| Part| QTY| Note
---|---|---|---
A21| Bolt M8 X 40 DIN 912| 12|
A22| Bolt M8 X 20 DIN 912| 24|
A23| Bolt M8 X 16 DIN 912| 18|
A24| Bolt M8 X 20 DIN 7991| 12| Countersunk.
A25| Bolt M8 X 20 DIN 7380-2| 4|
A26| Washer M8 DIN 125-A| 42|
A27| Washer M8 DIN 988| 12|
A28| Slot-Nut M8| 62|
BOX B – GT1-Pro Servo Mount HARDWARE KIT

#| Part| QTY| Note
B1| Servo mount left| 1|
B2| Servo mount right| 1|
B3| Bolt M8 X 40 DIN 912| 4|
B4| Bolt M8 X 25 DIN 912| 4|
B5| Washer M8 DIN 125-A| 16|
B6| Lock-Nut M8| 8|
Disclaimer: for some entries on this page, we supply more than required as spare materials. Don’t worry if you have some leftovers, this is intentional.

If you still have some questions regarding assembly of this product or about the manual itself, please refer to our support department. They can be reached at support@sim-lab.eu
Alternatively, we now have a Discord server where there are quite some experienced Sim-Lab customers hanging out. They might just help you along if you ask them nicely 😉 www.sim-lab.eu/discord
If you feel like printing this manual, please consider the environment before doing so. For the best results, make sure you print at 100% scale without borders.

Product page on the Sim-Lab website: