SIM LAB Triple Freestanding Vario Monitor Mount Instruction Manual

: June 13, 2024
: SIM-LAB

Table of Contents

BEFORE YOU START
Assembly Instructions
Customer Support
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SIM LAB Triple Freestanding Vario Monitor Mount

SIM LAB Triple Freestanding Vario Monitor Mount

BEFORE YOU START

Thank you for purchasing this Sim-Lab product! On the following pages, you will find detailed instructions on assembly. This requires only a set of simple tools and some of your time. Please check the bill of materials before starting (page 12) and make sure all the parts are delivered.

In this manual, we combined the single and triple integrated monitor mount. This is because we packaged the triple version as an upgrade to the single one.

This product combines some products we normally offer separately. We encourage you to read the product manuals for included products if this one doesn’t answer all of your questions. Please refer to the following if needed:
www.sim-lab.eu/xero-play-pivots-manual
www.sim-lab.eu/vario-vesa-manual

Inserting Slot-Nuts:

You got excited, finished the build, put the caps on, but forgot to install one element. Do not worry. It happens to everyone. In this diagram, you can see how to insert a Slot-Nut directly into the slot from the side. You can also use one of your smaller Hex wrenches to help wiggle the Slot-Nut in place.

Inserting Slot-Nuts

Tools needed:

Tools needed

Assembly Instructions

See assemble the other side of the Vario VESA.

If you purchased the ‘Triple Upgrade’, please continue on below.

Instructions for the right side (B2) are similar. Se below for the orientation of the profile.

Mind the orientation of the Slot-Nuts.

Adjust arm angles to your preference. We included markings in the pivots. Markings are placed in 10° increments.

When parts D9 and D10 are installed like above, monitors are easy to install in a neutral position. Parts D9 can be adjusted to change the tilt and/or height.

Parts D10 can be adjusted to adjust the monitor sideways if needed, and fix it in place.

BOX A – SINGLE MONITOR MOUNT PROFILE KIT

#| Part| QTY| Note
A1| 80X40 Length=1195mm| 1|
HARDWARE KIT
A2| Monitor side plate| 2|
A3| Integrated monitor corner bracket| 2|
A4| Profile 80×40 end-cap| 2|
A5| Bolt M8 X 35 DIN 912| 4|
A6| Bolt M8 X 30 DIN 912| 4|
A7| Bolt M8 X 16 DIN 912| 4|
A8| Cap-Washer M8| 8|
A9| Washer M8 DIN 988| 8|
A10| Washer M8 DIN 125-A| 8|
A11| Lock-Nut M8| 4|
A12| Slot-Nut M8| 8|
A13| Nut Cap M8| 4|
BOX B – TRIPLE MONITOR MOUNT PROFILE KIT

#| Part| QTY| Note
B1| 80X40 3N Length=580mm| 1| Left arm, engraved.
B2| 80X40 3N Length=580mm| 1| Right arm, engraved.
HARDWARE KIT
B3| Profile 80×40 end-cap| 4|
BOX C – Xero-Play triple pivot set HARDWARE KIT

#| Part| QTY| Note
C1| Xero-Play triple pivot adapter| 8|
C2| Bolt M8 X 40 DIN 912| 4|
C3| Bolt M8 X 25 DIN 912| 16|
C4| Nut M8| 4|
C5| Slot-Nut M8| 16|
BOX D – Vario VESA adapter set (x1 or x3 depending on purchase) HARDWARE KIT

#| Part| QTY| Note
D1| Vario VESA holder| 1|
D2| Vario VESA plate| 1|
D3| Vario VESA pin holder| 2|
D4| Vario VESA pin| 1|
D5| Bolt M5 X 20 DIN 7991| 4|
D6| Screw M4 X 16 DIN 7985| 4| Philips head.
D7| Screw M4 X 10 DIN 7985| 4| Philips head.
D8| Bolt M8 X 16 DIN 912| 2|
D9| Set screw M8 X 40 DIN 916| 3|
D10| Set screw M5 X 20 DIN 916| 2|
D11| Washer M8 DIN 125-A| 2|
D12| Slot-Nut M8| 2|
D13| Standoff M4 x 10| 4|
Disclaimer: for some entries on this page, we supply more than required as spare materials. Don’t worry if you have some leftovers, this is intentional.

Customer Support

If you still have some questions regarding assembly of this product or about the manual itself, please refer to our support department. They can be reached at support@sim-lab.eu

Alternatively, we now have a Discord server where there are quite some experienced Sim-Lab customers hanging out. They might just help you along if you ask them nicely 😉
www.sim-lab.eu/discord

If you feel like printing this manual, please consider the environment before doing so. For the best results, make sure you print at 100% scale without borders.
Product page on the Sim-Lab website: