SIM LAB Quad Add-On Quad Monitor Stand Instruction Manual
- June 13, 2024
- SIM-LAB
Table of Contents
SIM LAB Quad Add-On Quad Monitor Stand
Product Information
- Product Name: Quad Add-On
- Version: 1.2
- Last updated: 11-10-2023
Description
The Quad Add-On is a product from Sim-Lab that is designed for assembly and
installation. It comes with various components and hardware to build a sturdy
structure for your equipment.
Product Usage Instructions
- Before starting the assembly, please check the bill of materials provided on page 10 of the user manual to ensure that all the necessary parts are delivered.
- Inserting Slot-Nuts:
- To insert a Slot-Nut into the slot from the side, refer to the diagram provided in the user manual.
- You can use a smaller Hex wrench to help wiggle the Slot-Nut in place.
- Breaking tabs:
- Sometimes, tabs from corner brackets need to be broken off to fit as instructed.
- To break off the tabs, place a flathead screwdriver behind the tab and tilt upwards.
- Always ensure that you point away from yourself while doing so.
- Assembly Steps:
- Refer to the provided diagram and gather the necessary tools: a 4/6MM hex wrench, a 22 | 11 hex wrench, and a 320MM slot-nut M8 slot-nut M6 (A15).
- Follow the instructions for each step, indicated by the corresponding symbols, brackets, and part numbers.
- Use the provided hardware kit components, such as corner brackets, washers, bolts, screws, and slot nuts, as specified in the user manual.
- Repeat the necessary steps to build the desired structure.
- Refer to the provided diagram and gather the necessary tools: a 4/6MM hex wrench, a 22 | 11 hex wrench, and a 320MM slot-nut M8 slot-nut M6 (A15).
- If you have any questions or need assistance with the assembly process or the user manual itself, you can contact Sim-Lab’s support department at support@sim-lab.eu.
- Alternatively, you can join Sim-Lab’s Discord server where experienced customers can provide assistance. Visit www.sim-lab.eu/discord for more information.
- For environmental considerations, it is recommended to avoid printing the manual unless necessary. If you choose to print, ensure it is at 100% scale without borders for the best results.
PROFILE KIT
#| Part| QTY| Note
P1| 80X40 Length=320mm| 1|
P2| 40X40 Length=320mm| 4|
HARDWARE KIT
A3| VESA 200 adapter| 1|
A4| Pivot plate| 2|
A5| Corner bracket 40×40| 8|
A6| Corner bracket 40×40 cap| 8|
A7| Profile 40×40 end-cap| 6|
A8| Bolt M8 X 16 DIN 912| 24|
A9| Bolt M6 X 16 DIN 7991| 4|
A10| Washer M8 DIN 125-A| 24|
A11| Screw Philips M4 X 16 DIN 7985| 4| Extra
A12| Screw Philips M4 X 10 DIN 7985| 4| Extra
A13| Spacer male/female M4 X 10| 4| Extra
A14| Slot-Nut M8| 24|
A15| Slot-Nut M6| 4|
Disclaimer: for some entries on this list, we supply more than required as
spare materials. Don’t worry if you have some leftovers, this is intentional.
Note
Some spare materials may be included in the package. This is intentional
and should not cause concern if there are leftovers.
Product Page
Visit the Sim-Lab website for more information about the product: [product
page URL]
BEFORE YOU START
Thank you for purchasing this Sim-Lab product! On the following pages, you will find detailed instructions on assembly. This requires only a set of simple tools and some of your time. Please check the bill of materials before starting (page 10) and make sure all the parts are delivered.
Inserting Slot-Nuts
You got excited, finished the build, and put the caps on, but forgot to install one element. Do not worry. It happens to everyone. In this diagram, you can see how to insert a Slot-Nut directly into the slot from the side. You can also use one of your smaller Hex wrenches to help wiggle the Slot-Nut in place.
Breaking tabs
Sometimes tabs from corner brackets need to be broken off in order to fit as
instructed. Place a flathead screwdriver behind the tab and tilt upwards.
Always make sure to point away from you while doing so.
To know when to do this, we will show the following symbol next to the
brackets.
Tools needed
Disclaimer: for some entries on this list, we supply more than required as
spare materials. Don’t worry if you have some leftovers, this is intentional.
If you still have some questions regarding the assembly of this product or
about the manual itself, please refer to our support department. They can be
reached at support@sim-lab.eu Alternatively, we
now have a Discord server where there are quite some experienced Sim-Lab
customers hanging out. They might just help you along if you ask them nicely 😉
www.sim-lab.eu/discord If you feel like
printing this manual, please consider the environment before doing so. For the
best results, make sure you print at 100% scale without borders.
Product page on the Sim-Lab website: