acer W510 Tablet PC User Guide
- June 5, 2024
- Acer
Table of Contents
Tablet PC
Quick Star Guide
Acer One 10 T8-129L
PRODUCT SAFETY INFORMATION
fOR YOUR SAFTY
Please read this manual before using the cell smart device (Phone/Tablet) to
ensure safe and proper use.
H
SWITCH OFF IN HOSPITALS
Please abide by relevant provisions or regulations. Please turn off your mobile
smart device (Phone/Tablet) near medical equipment.
SWITCH OFF WHEN REFUELING
Don’t use the smart device (Phone/Tablet) at a refueling point. Don’t use near
fuel or chemicals
SIM AND SD CARDS ARE PORTABLE
Keep your smart device (Phone/Tablet), smart device (Phone/Tablet) parts and
accessories out of children’s reach.
BATTERY
Please do not destroy or damage the battery, it can be dangerous and cause
fire.
Please do not throw the battery in fire to avoid hazards.
When the battery cannot be used, please dispose of it in safe environment.
Do not try to dismantle the battery.
If the battery or the charger is broken or old, please stop using them, and
replace with a certified genuine battery.
USE QUALITY EQUIPMENT
Use authorized equipment to avoid danger.
ROAD SAFETY COMES FIRST
Give full attention while driving, Park before using your smart device
(phone/tablet). Please follow the traffic rules of local city town.
INTERFERENCE
All wireless devices may be susceptible to cause interference, which could
affect performance.
SWITCH OFF IN AIRCRAFT
Wireless devices can cause interference in aircraft. It’s not only dangerous
but also illegal to use mobile smart device (Phone/Tablet) in an aircraft.
RADIOFREQUENCY EXPOSITION
General statement on radio frequency and RF energy
Your smart device (phone/tablet) contains a transmitter and a receiver. When
it is ON, receives and transmits RF energy. When you communicate with your
smart device (phone/tablet) , the system handling your call controls the power
level at which your smart device (phone/tablet) transmits.
Specific absorption rate (SAR)
Your smart device (Phone/Tablet) is a radio transmitter and receiver. It is
designed not to exceed the limits for exposure to radio waves recommended by
international guidelines. These guidelines were developed by the independent
scientific organization ICNIRP and include safety margins designed to ensure
the protection of all persons, regardless of age and health. As SAR is
measured utilizing the device’s highest transmitting power, the actual SAR of
this device while operating is typically below that indicated above. This is
due to automatic changes to the power level of the device to ensure it only
uses the minimum power required to communicate with the network. Important
safety information regarding radiofrequency radiation (RF) exposure. To ensure
compliance with RF exposure guidelines the smart device (phone/tablet) must be
used with a inimum of 5 mm separation from the body
LIMITING EXPOSURE TO RADIO FREQUENCY (RF) FIELDS
For individuals concerned about limiting their exposure to RF fields, the World
Health Organization (WHO) provides the following advice:
Precautionary measures: present scientific information does not indicate the
need for any special precautions for the use of the mobile smart device
(phone/tablet). If individuals are concerned, they might choose to limit their
own or their children’s RF exposure by limiting the length of calls, or using
‘hands-free’ devices to keep the mobile smart devices (phone/ tablet) away
from the head and body.
REGULATORY INFORMATION
This equipment is in compliance with the essential requirements and other
relevant provisions of the Directive.
This equipment is in compliance with the essential requirements and other
relevant provisions of the Directive.
PROTECTION AGAINST THEFT
Your smart device (phone/tablet) is identified by an IMEI (smart device
(Phone/Tablet) serial number) shown on the packaging label and in the
product’s memory. We recommend that you note the number the first time you use
your smart device (phone/tablet) by entering *# 0 6 # and keep it in a safe
place.
It may be requested by the police or your operator if your smart device
(phone/tablet) is stolen. This number allows your smart device (phone/tablet)
to be blocked preventing a third person from using it, even with a different
SIM card.
This symbol on your smart device (Phone/Tablet), the battery and the
accessories means that these products must be taken to collection points at
the end of their life:
– Municipal wasted disposal centers with specific bins for these items of
equipment.
– Collection bins at points od sale.
They will then be recycled, preventing substances being disposed of in the
environment, so that their components can be reused.
CONTENT OF THE BOX
acer offer multiple accessories included in the box.
- USB Cable
- Earphone
- Charger
- User manual
PRODUCT OVERVIEW
– Reset
Press and hold the reset button on the side of the device for 3 seconds to
reset the system and shut.
– Insert SIM Card and SD Card
Open the slot cover as the picture shows
Charge the Battery
Charge the Battery for at 6 hours before using it the first time. Connect the
USB cable to the USB power adaptor, and then plug the end of the USB cable
into the USB Port.
Please put the smart device (Phone/Tablet) on charge when the battery is at
10%.
FUNCTION KEYS
Power button | Short press to sleep/wake up, long press to starup and shutdown. |
---|---|
Volume + (up) | increase the volume |
Volume – (down) | decrease the volume |
HOME button (home) | Click it in any interFace will return to main interFace. |
Back button (back) | Click it in any interFace will return to previous menu. |
Menu button | This button will display in menu interFace. |
Setting button | Display recently browsed history |
GETTING STARTED
5.1 Home screen
From the Home screen, you can view your device’s status and Access the
application The Home screen has multiple panels. Scroll left or right to view
the panels on the Home screen.
5.2 Access applications
– Scroll down or up to another screen, and select an application.
– Press to return to the previous screen, and press to return to the Home
screen.
5.3 Manage applications
– In the idle screen, tap Settings > Apps
– Tap Running, you can view all the running apps, tap this app to enter it,
you can tap Stop to choose to stop running
– Tap Downloaded, you can view all the downloaded apps, tap app to enter it,
you can check the detailed information of this app, tap Uninstall to unload it
DEVICE’S STATE AND NOTICE
Iconography (Icons) for notification
When a prompt message appears, click the column box and slide on the screen
with your finger to open the notice list. Click the options needed to check to
see detailed information. Then you may click the message box and slide upwards
to close the message window. The following are iconography for icons in the
status bar:
| Gmail TM| | Airplane Mode turned on
---|---|---|---
| Return button| | Downloading
| Display recently-used application| | Home button
| Current electric volume,| | WIFI connected, Internet is available
| Phone| | Messaging
| Contact List| | Bluetooth function
TROUBLESHOOTING
Problem | Solution |
---|---|
The device will turn itself off after a Few seconds | Check that the battery is |
charged.
No sound is heard| Adjust the volume level check if audio File is broken
Screen is hard to see in bright light.| Adjust sceen in the system the menu.r
Avoidbrightness using the reader in direct sunlight.
Data on the screen is corrupted or a program is not responding properly| Check
if the device is correctly connected to the computer.
Check if the memory space is Full. Check if the USB cable is broken
WARNINGS AND NOTES
Operational Warnings
IMPORTANT INFORMATION ON SAFF AND EFFICIENT OPERATION. Read this information
before
using your smart device (phone/tablet). For the safe and efficient operation of
your smart device (Phone/Tablet), observe these guidelines:
Potentially explosive at atmospheres
Turn off your smart device (phone/tablet) when you are in any areas with a
potentially explosive atmosphere, such as fueling areas (gas or petrol
stations, below deck on boats), storage facilities for fuel or chemicals,
blasting areas and areas near electrical blasting caps, and areas where there
are chemicals or particles (Such as metal powders, grains, and dust) in the
air.
Interference to medical and personal electronic devices
Most but not all electronic equipment is shielded from RF signals and certain
electronic equipment may not be shielded against the RF signals from your
smart device (phone/tablet).
Audio safety
This smart device (phone/tablet) is capable of producing loud noises which may
damage your hearing. When using the speaker smart device (phone/tablet)
feature, it is recommended that you place your smart device (phone/tablet) at
a safe distance from your ear.
Other medical devices, hospitals
If you use any other personal medical device, consult the manufacturer of your
device to determine if it is adequately shielded from external RF energy. Your
physician may be able to assist you in obtaining this information. Turn your
smart device (phone/tablet) OFF in health care facilities when any regulations
posted in these areas instruct you to do so. Hospitals or health care
facilities may be using equipment that could be sensitive to external RF
energy.
Product statement on handling and use
You alone are responsible for how you use your smart device (phone/tablet) and
any consequences of its use.
You must always switch off your smart device (phone/tablet) wherever the use of
a smart device (Phone/Tablet) is prohibited. Use of your smart device
(phone/tablet) is subject to safety measures designed to protect users and
their environment.
Always treat your smart device (phone/tablet) and its accessories with care
and keep it in a clean and dust-free place
- Do not expose your smart device (phone/tablet) or its accessories to open flames or lit tobacco products.
- Do not expose your smart device (phone/tablet) or its accessories to liquid, moisture, or high humidity.
- Do not drop, throw, or try to bend your smart device (phone/tablet) or its accessories.
- Do not use harsh chemicals, cleaning solvents, or aerosols to clean the device or its accessories.
- Do not attempt to disassemble your smart device (phone/tablet) or its accessories; only authorized personnel must do so.
- Do not expose your smart device (phone/tablet) or its accessories to extreme temperatures, minimum 32ºF and maximum 113ºF (0ºC to 45ºC).
Due to the used enclosure material, the product shall only be connected to a USB Interface of version 2.0 or higher. The connection to so-called power USB is prohibited. The adapter shall be installed near the equipment and shall be easily accessible.
Battery
Your smart device (phone/tablet) includes an internal lithium-ion or lithium-
ion polymer battery. Please note that use of certain data applications can
result in heavy battery use and may require frequent battery charging. Any
disposal of the smart device (phone/tablet) or battery must comply with laws
and regulations pertaining to lithium-ion or lithium-ion polymer batteries.
CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE
OF USED BATTERIES ACCORDING TO THE INSTRUCTION.
Faulty and damaged products
Do not attempt to disassemble the smart device (phone/tablet) or its
accessory. Only qualified personnel must service or repair the smart device
(phone/tablet) or its accessory. If your smart device (Phone/Tablet) or its
accessory has been submerged in water, Punctured, or subjected to a severe
fall, do not use it until you have taken it to be checked at an authorized
service center.
FCC Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions (1)this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Gmail is a
trademark of Google LLC.
SAR Information Statement
Your Tablet PC is a radio transmitter and receiver. It is designed and
manufactured not to exceed the emission limits for exposure to radiofrequency
(RF) energy set by the Federal Communications Commission of the U.S.
Government. These limits are part of comprehensive guidelines and establish
permitted levels of RF energy for the general population. The guidelines are
based on standards that were developed by independent scientific organizations
through periodic and thorough evaluation of scientific studies. The standards
include a substantial safety margin designed to assure the safety of all
persons, regardless of age and health. The exposure standard for wireless
mobile phones employs a unit of measurement known as the Specific Absorption
Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg. Tests for SAR are
conducted with the phone transmitting at its highest certified power level in
all tested frequency bands. Although the SAR is determined at the highest
certified power level, the actual SAR level of the phone while operating can
be well below the maximum value. This is because the phone is designed to
operate at multiple power levels so as to use only the power required to reach
the network. In general, the closer you are to a wireless base station
antenna, the lower the power output. Before a phone model is available for
sale to the public, it must be tested and certified to the FCC that it does
not exceed the limit established by the government adopted requirement for
safe exposure. The tests are performed in positions and locations (e.g., at
the ear and worn on the body) as required by the FCC for each model. The
highest SAR value for this model phone when worn on the body, as described in
this user guide, is 0.55 W/Kg (Body-worn measurements differ among phone
models, depending upon available accessories and FCC requirements). While
there may be differences between the SAR levels of various phones and at
various positions, they all meet the government requirement for safe exposure.
The FCC has granted an Equipment Authorization for this model phone with all
reported SAR levels evaluated as in compliance with the FCC RF exposure
guidelines. SAR information on this model phone is on file with the FCC and
can be found under the Display Grant section of
http://www.fcc.gov/oet/fccid after searching on
FCC ID: 2AMY3-ACERT8129L Additional information on Specific Absorption Rates
(SAR) can be found on the Cellular Telecommunications Industry Association
(CTIA) web-site at http://www.wow-com.com. In the United States and
Canada, the SAR limit for mobile phones used by the public is 1.6 watts/kg
(W/kg) averaged over one gram of tissue. The standard incorporates a
substantial margin of safety to give additional protection for the public and
to account for any variations in measurements. The SAR test distance is 0mm.
CE Statement
Herby, HUNAN GREAT WALL COMPUTER SYSTEM CO., LTD declares that this Tablet PC,
Acer
One 10 T8-129L is in compliance with the essential requirements and other
relevant provisions of Directive 2014/53/EU. In accordance with Article 10(2)
and Article 10(10), this product is allowed to be used in all EU member
states.
Use the Tablet PC in an environment with a temperature between 0℃ and 45℃ Use
careful with the earphone may be possible excessive sound pressure from
earphones and
headphones can cause hearing loss.
Risk of explosion if the battery is replaced by an incorrect type. Dispose of
used batteries according to the instructions.
The product shall only be connected to a USB interface of version USB2.0 SAR:
The device complies with RF specifications when the device used at 0mm from
your body.
The highest SAR value for this device when tested for use was 0.39W/Kg(10g)
for the body.
The adapter shall be installed near the equipment and shall be easily
accessible.
The plug is considered as a disconnect device of the adapter
Adapter Model: JK050200-S37EUVU
Input: AC 100-240V, 50/60Hz, 0.5A Output: DC 5.0V, 2.0A, 10.0W
Operation Frequency:
For BT/BLE: 2402MHz~2480MHz
For 2.4G WIFI: 2412MHz~2472MHz (802.11b/802.11g/802.11n(HT20)) 2422MHz~2462MHz
(802.11n(HT40))
For 5G WIFI: 5150MHz~5250MHz, 5725MHz~5875MHz
For GSM: E-GSM 900/GPRS 900/EGPRS 900:
TX: 880MHz~915MHz; RX: 925MHz~960MHz GSM 1800/GPRS 1800/EGPRS 1800:
TX: 1710MHz~1785MHz; RX: 1805MHz~1880MHz
For WCDMA:
UTRA Band I:
TX:1920MHz~1980MHz; RX: 2110MHz~2170MHz
UTRA Band VIII:
TX: 880MHz~915MHz; RX: 925MHz~960MHz
For FM: 87.5MHz-108MHz
For GPS: 1.57542GHz
For LTE:
LTE Band 1: (UL)1920MHz~1980MHz, (DL)2110MHz~2170MHz
LTE Band 3: (UL)1710MHz~1785MHz, (DL)1805MHz~1880MHz
LTE Band 40: (UL)2300MHz~2400MHz, (DL)2300MHz~2400MHz
Max output power:
For BT: 0.014W BLE: 0.0005W For 2.4G Wifi: 0.0693W For 5G Wifi: 0.0199W
For GSM900: 1.8261W For GSM1800: 1.1482W
For WCDMA Band1: 0.2128W For WCDMA Band2: 0.2312W
For LTE Band1: 0.1648W For LTE Band3 : 0.2438W
For LTE Bnad40: 0.15W
Manufacturer: HUNAN GREAT WALL COMPUTER SYSTEM CO., LTD
Address: HUNAN GREAT WALL INDUSTRIAL PARK, TIANYI SCIENCE AND TECHNOLOGY CITY,
XIANG YUN MIDDLE ROAD, TIANYUAN DISTRICT, ZHU ZHOU, HUNAN PROVINCE, CHINA
Tel: +860755-38998939
Fax: N/A
E-mail: (huanglecong@greatwall.com.cn
DECLARATION OF CONFORMITY
I hereby declare that the product
Product:
Product Name: Tabet PC
Made I: .Aoer one 10 78-12 3L, Ade r_One_10 TB-129L
Brand Name: .Acer
Hardware Version: G853HH_V1
Software Version: P PR1 .180161 0.011 release-keys
Accessories:
sorriest Adapter Information:
Mode I: -.11<050200-S37EUVU
Input: AC 100-240V. 50/60 Hz, 0 .5A
Output: DC 5. DV, 2.0A, 10.0W
Manufacturer SHENZHEN JUKE ELECTRONICS CO., LTD
USB Cable Information:
Mode 2 7 25#23+22
Length: 1 M rlsnufscturer: She hen Zhengythein Electron lc Technology Co., LTD
Battery information: Model: LITL3 13281 P-2P
Specification: 3 .1, 6600 n-An . 2 4 .42’Wh
Manufacturer. JI VAN UTILITY TE CHNOLOGYCO., LTD.
{Name product, type time a model, batch or serial number: sets-resell the
technical regulations ap Oita We to the p rod Le within the scope of Council
Directives 20141531E0.20141351E0 and 2014130/EU: and declare that the sa rne
application has not been lodged with a rry other notified body.
EN 82308-1:2014+AI 1:2017 EN 50803:2017
EN 82479:2010
EN 62209-2:2010
EN 50566:2017 DraftETSI
EN 301 489-52V1.1.0 (2016-11)
ETSI EN:301 489-19 V2.1.11(2019-04)
Draft ETSI EN 301 489-17V32.2 (2019-12)
ETSI EN 301 489-3V2.1.1(201946)
ETSI EN 301 489-1 V2.2.3 (2019-11)
EN 55032: 2015
EN 55035: 2017
EN 61000-3-2:2014
EN 61000-3-3:2013| ETSI EN 300 328 V2.2.2 (2019-07)
ETSI EN 301:893 V2.1.1 (2017-05)
ETSI EN 300 440 V221 (2018-07)
ETSI EN 301 511 V12.5.1 (2017-03)
ETSI EN 301 908-1V13.1.11(2019-11)
ETSI EN 301 908-2V11.1.2 (2017-08)
ETSI EN:301 908-13 V13.1.1 (2019•11)
ETSI EN:303 413 V1.1.1 (2017-06)
ETSI EN 303 345-1 V1.1.1(2019416)
Draft ETSI EN 303 345-3 V1.1.012019-11)
---|---
Titel(s) Mega:Vans, standards,
All essential radio test suites have been carried out
NOTIFIED BODY: Mr001,1L3CE –
Address :
575 Boulder Court,
Pleasanton, Califomis94566
USA
Identification Number 2280
MANUFACTURER or AUTHORISED REPRESENTATIVE: – Address:
HUNAN GREATVVAL L COMPUTER SYSTEM CO., LTD HUNAN GREATNALL INDUSTRIAL PARK
TIANYI SCIENCE AND -TECHNOLOGY CITY, XIANGYUN MIDDLE ROAD, TIANYUAN DISTRICT,
ZHUZHOU, HUNAN PROVINCE, CHI NA
This declaration is issued under the sole responsibility of the manufacturer
and, if applicable, his authorized representative.
Point of contact: Huang le Cong , +860755-26719939-8111 /N/A
Name. Mare and tax ‘unbar)
2020-08-07
(place, daie of issue)
(Signature)
Huang le cong, Safety engineer
sarre and tie NI DOCK MSC
Documents / Resources
| acer
W510 Tablet
PC
[pdf] User Guide
ACERT8129L, 2AMY3-ACERT8129L, 2AMY3ACERT8129L, W510, Tablet PC, W510 Tablet
PC, Tablet PC
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>