SIM LAB GT1-Pro Integrated Triple Monitor Mount Instruction Manual

June 13, 2024
SIM-LAB

SIM-LAB-LOGO.

SIM LAB GT1-Pro Integrated Triple Monitor Mount

SIM-LAB-GT1-Pro-Integrated-Triple-Monitor-Mount-
product

Product Information

  • Product Name: GT1-PRO Integrated Triple Monitor Mount
  • Version: 1.0
  • Last Updated: 19-07-2023
  • Manufacturer: Sim-Lab

Product Usage Instructions

Before You Start

Thank you for purchasing the GT1-PRO Integrated Triple Monitor Mount. Before starting the assembly, please check the bill of materials on page 14 of the manual to ensure that all the parts are delivered.

Inserting Slot-Nuts:

If you forgot to install a Slot-Nut during the build, you can insert it directly into the slot from the side. You can use a smaller Hex wrench to help wiggle the Slot-Nut in place.

Breaking Tabs:

Sometimes, tabs from corner brackets need to be broken off to fit as instructed. To break off a tab, place a flathead screwdriver behind the tab and tilt upwards. Always ensure that you point away from yourself while doing so. The manual will indicate when to break off tabs using the symbol next to the brackets.

Tools Needed:

  • 6MM Allen Key
  • 22 | 15 Allen Key
  • 500MM Profile 40X40
  • Slot-Nut M8
  • End-Cap (1X)
  • End-Cap (2X)
  • Corner Bracket*
  • M8 X 16 Washer
  • M8 Slot-Nut
  • Integrated Bracket
  • M8 X 25 Cap-Washer
  • Pivot Adapter
  • M8 X 25 Slot-Nut
  • M8 X 40 Nut M8
  • Vario VESA Holder
  • Vario VESA Plate
  • Pin Holder
  • Pin
  • M5 X 20 (Set Screw)
  • M8 X 40 (Set Screw)

Assembly:

Please refer to the provided diagram and the corresponding parts list in Boxes A and B of the manual for the step-by-step assembly instructions. Follow the instructions carefully to build your GT1-Pro cockpit and fit it with the GT1-Pro Integrated Triple Monitor Mount.

Adjusting Monitors:

Once parts D12 and D13 are installed as shown in the manual, monitors can be easily installed in a neutral position. Part D12 can be adjusted to change the tilt and/or height, while part D13 can be adjusted to adjust the monitor sideways if needed and fix it in place.
Please note that if you have any additional questions or need further assistance, you can refer to the product manuals for the included products or visit the following links:
Enjoy using your GT1-PRO Integrated Triple Monitor Mount!

BEFORE YOU START

Thank you for purchasing this Sim-Lab product! On the following pages, you will find detailed instructions on assembly. This requires only a set of simple tools and some of your time. Please check the bill of materials beforestarting (page 14) and make sure all the parts are delivered.
This manual presumes you are building your GT1-Pro cockpit and fitting it with the GT1-Pro integrated triple monitor mount. For logistical reasons, the GT1-Pro integrated triple monitor mount hardware kit is an add-on to the GT1-Pro integrated single monitor mount.
We encourage you to read the product manuals for included products if this one doesn’t answer all of your questions. Please refer to the following if needed:

www.sim-lab.eu/xero-play-pivots-manual
www.sim-lab.eu/vario-vesa-manual

Inserting Slot-Nuts:

You got excited, finished the build, put the caps on, but forgot to install one element. Do not worry. It happens to everyone. In this diagram, you can see how to insert a Slot-Nut directly into the slot from the side.
You can also use one of your smaller Hex wrenches to help wiggle the Slot-Nut in place.

Breaking tabs:
Sometimes tabs from corner brackets need to be broken off in order to fit as instructed. Place a flathead screwdriver behind the tab and tilt upwards .SIM-LAB-GT1-Pro-Integrated-Triple-Monitor-Mount-fig-
\(2\)
Always make sure to point away from you while doing so. To know when to do this, we will show the following symbol next to the brackets

Tools needed:SIM-LAB-GT1-Pro-Integrated-Triple-Monitor-Mount-fig-
\(3\)

INSTALLATION

SIM-LAB-GT1-Pro-Integrated-Triple-Monitor-Mount-fig-
\(4\) SIM-LAB-GT1-Pro-Integrated-
Triple-Monitor-Mount-fig- \(5\) SIM-LAB-GT1-Pro-Integrated-Triple-Monitor-Mount-fig-
\(6\) SIM-LAB-GT1-Pro-Integrated-
Triple-Monitor-Mount-fig- \(7\) SIM-LAB-GT1-Pro-Integrated-Triple-Monitor-Mount-fig-
\(8\) SIM-LAB-GT1-Pro-Integrated-
Triple-Monitor-Mount-fig- \(9\) SIM-LAB-GT1-Pro-Integrated-Triple-Monitor-Mount-fig-
\(10\) SIM-LAB-GT1-Pro-Integrated-
Triple-Monitor-Mount-fig- \(11\) SIM-LAB-GT1-Pro-Integrated-Triple-Monitor-Mount-fig-
\(12\) SIM-LAB-GT1-Pro-Integrated-
Triple-Monitor-Mount-fig- \(13\) SIM-LAB-GT1-Pro-Integrated-Triple-Monitor-Mount-fig-
\(14\)

BOX CONTENT

BOX A – GT1-Pro Integrated Monitor Mount PROFILE KIT

#| Part| QTY| Note
A1| 40X40 Length=600mm| 1| Only for integrated single.
A2| 40X40 Length=500mm| 2|
HARDWARE KIT
A3| Integrated bracket| 2|
A4| Corner bracket 40×40| 2|
A5| Corner bracket 40×40 cap| 2|
A6| Profile 40×40 end-cap| 4|
A7| Bolt M8 X 25 DIN 912| 8|
A8| Bolt M8 X 16 DIN 912| 4|
A9| Cap-Washer M8| 8|
A10| Washer M8 DIN 125-A| 4|
A11| Slot-Nut M8| 12|
BOX B GT1-Pro Integrated Triple Monitor Mount PROFILE KIT

#| Part| QTY| Note
B1| 40X40 Length=850mm| 1| Replaces A1.
B2| 40X40 Length=500mm| 2|
HARDWARE KIT
B3| Corner bracket 40×40| 2|
B4| Corner bracket 40×40 cap| 2|
B5| Profile 40×40 end-cap| 6|
B6| Bolt M8 X 16 DIN 912| 4|
B7| Washer M8 DIN 125-A| 4|
B8| Slot-Nut M8| 4|
BOX C – Xero-Play Triple Pivot Set HARDWARE KIT

#| Part| QTY| Note
C1| Xero-Play triple pivot adapter| 8|
C2| Bolt M8 X 40 DIN 912| 4|
C3| Bolt M8 X 25 DIN 912| 16|
C4| Nut M8| 4|
C5| Slot-Nut M8| 16|
BOX D – Vario VESA Single Adapter (X3) HARDWARE KIT

#| Part| QTY| Note
D1| Vario VESA holder| 1|
D2| Vario VESA plate| 1|
D3| Vario VESA pin holder| 2|
D4| Vario VESA pin| 1|
D5| Bolt M6 X 12 DIN 7991| 4| Used with VESA 100/200 adapter.
D6| Bolt M5 X 20 DIN 7991| 4|
D7| Bolt M4 X 16 DIN 7985| 4| Philips head.
D8| Bolt M4 X 10 DIN 7985| 4| Philips head.
D9| Bolt M8 X 16 DIN 912| 2|
D10| Bolt M6 X 16 DIN 912| 4|
D11| Bolt M5 X 16 DIN 912| 4|
D12| Set screw M8 X 40 DIN 916| 3|
D13| Set screw M5 X 20 DIN 916| 2|
D14| Washer M8 DIN 125-A| 2|
D15| Slot-Nut M8| 2|

If you still have some questions regarding assembly of this product or about the manual itself, please refer to our support department. They can be reached at support@sim-lab.eu
Alternatively, we now have a Discord server where there are quite some experienced Sim-Lab customers hanging out. They might just help you along if you ask them nicely 😉 www.sim-lab.eu/discord
If you feel like printing this manual, please consider the environment before doing so. For the best results, make sure you print at 100% scale without borders.

Product page on the Sim-Lab website:

SIM-LAB-GT1-Pro-Integrated-Triple-Monitor-Mount-fig-
\(15\)

Documents / Resources

| SIM LAB GT1-Pro Integrated Triple Monitor Mount [pdf] Instruction Manual
GT1-Pro, GT1-Pro Integrated Triple Monitor Mount, Integrated Triple Monitor Mount, Triple Monitor Mount, Monitor Mount, Mount
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals