SIM LAB P1-X PRO Sim Racing Cockpit Instruction Manual

June 13, 2024
SIM-LAB

SIM LAB P1-X PRO Sim Racing Cockpit

SIM LAB P1-X PRO Sim Racing Cockpit

BEFORE YOU START

Thank you for purchasing this Sim-Lab product! On the following pages, you will find detailed instructions on assembly. This requires only a set of simple tools and some of your time. Please check the bill of materials before starting (pages 23/24) and make sure all the parts are delivered.

For the angled profiles, the lengths in the bill of materials might not perfectly match the length of the part you measure. Don’t worry, we measure differently when cutting the profiles and with the angles as they are, the given dimensions are a close approximation.

We tried to go with a different style of assembly for this one. Don’t panic if you can’t find any corner brackets included in the hardware bags.

Inserting Slot-Nuts

You got excited, finished the build, put the caps on, but forgot to install one element. Do not worry. It happens to everyone. In this diagram, you can see how to insert a Slot-Nut directly into the slot from the side. You can also use one of your smaller Hex wrenches to help wiggle the Slot-Nut in place.

BEFORE YOU START

Tools needed

Tools needed

Assembly Instructions

Tools needed

Note: the counterbores should point (arrows) to the outside of the cockpit.

Assembly Instructions
Tools needed
Assembly Instructions
Tools needed
Assembly Instructions
Assembly Instructions
Assembly Instructions
Assembly Instructions
Assembly Instructions
Assembly Instructions
Assembly Instructions
Assembly Instructions

If you purchased the ‘Front Mount’, please see the next page.

Normal assembly resumes with the ‘Side Mount’ on page 19

Assembly Instructions

If you purchased the ‘Fanatec DD Mount’, please see page 16.

Normal assembly continues on the next page.

The Front Mount Spacer (E5) is an optional part and may not be included in your hardware kit at the time of writing

Assembly Instructions

The Front Mount Spacer (E5) is an optional part and may not be included in your hardware kit at the time of writing

Assembly Instructions

*Fanatec DD1/DD2 does NOT need the CSL Spacer.

The Front Mount Spacer (F4) is an optional part and may not be included in your hardware kit at the time of writing.

Assembly Instructions

The Front Mount Spacer (F4) is an optional part and may not be included in your hardware kit at the time of writing

Assembly Instructions

Part numbers for Fanatec DD Mount differ.

Assembly Instructions
Assembly Instructions
Assembly Instructions
Assembly Instructions
Assembly Instructions

BOX A – P1-X Pro PROFILE KIT

# Part QTY Note
A1 160X40 UL Length=1350mm 2
A2 160X40 UL Length=500mm 1
A3 160X40 UL Length=490mm 1
A4 120X40 Length=850mm 2
A5 80X40 Length=500mm 1
A6 80X40 Length=300mm 1
A? 40X40 Length=500mm 2

HARDWARE KIT

AB| Corner bracket 160×40| 2|
---|---|---|---
A9| Profile 160×40 end-cap| 2|
A10| Profile 120×40 end-cap angled| 4|
A11| Profile 80×40 end-cap angled| 1|
A12| Profile 80×40 end-cap| 1|
A13| Profile 40×40 end-cap| 4|
A14| Upright sandwich plate LEFT| 1|
A15| Upright sandwich plate RIGHT| 1|
A16| Side mount sandwich plate| 1|
A17| Side mount bracket| 2|
A18| Bolt MB X 40 DIN 912| 8|
A19| Bolt MB X 25 DIN 912| 18|
A20| Bolt MB X 20 DIN 912| 8|
A21| Bolt MB X 20 DIN 7991| 10| Countersunk.
A22| Cap-Washer MB| 10|
A23| Washer MB DIN 988| 18|
A24| Washer MB DIN 125-A| 8|
A25| Slot-Nut MB| 28|

BOX B – Sim Feet HARDWARE KIT

Part| QTY| Note

---|---|---
81| Foot support plate| 4|
B2| Foot| 4| Threaded ball-joint rod fitted.
83| Bolt M8 X 25 DIN 912| 8|
B4| Washer M16 DIN 125- A| 8|
85| Nut M16| 8| 4 pre – fitted.
B6| Slot-Nut MB| 8|

BOX C – Pedal Deck PROFILE KIT

 # Part QTY Note
C1 160X40 Length=470mm
C2 80X40 Length=470mm

HARDWARE KIT
C3| Pedal deck bracket| 2|
C4| Bolt M8 X 40 DIN 912| 6|
C5| Bolt M8 X 30 DIN 912| 8|
C6| Bolt M6 X 16 DIN 912| 12| Extra.
C?| Bolt M5 X 16 DIN 912| 12| Extra.
CB| Cap- Washer M8| 14|
C9| Washer M8 DIN 988| 14|
C10| Slot- Nut M8| 6|
C11| Slot-Nut M6| 12| Extra.
C12| Slot- Nut M5| 12| Extra.

Disclaimer: for some entries on this page, we supply more than required as spare materials. Don’t worry if you have some leftovers, this is intentional.

BOX D -Wheel Deck (optional purchase) HARDWARE KIT

| Part|   QTY|   Note

---|---|---|---
 01| Wheel deck|  1| **
 02| Bolt M8 X 50 DIN 912|
2| **
 03| Bolt M8 X 20 DIN 912| 2| **
 04| Washer M8 DIN 125-A|
4| **
 05|  Slot-Nut M8| 4| ****

BOX E – Front Mount (optional purchase) PROFILE KIT

| Part| QTY| Note

---|---|---|---
E1| 120X40 UL Length=192mm| 2
| HARDWARE KIT|
E2| Front mount| 1
E3| Front mount bracket A| 2
E4| Front mount bracket B| 2
ES| Front mount spacer*| 12| Optional part.
E6| Bolt M8 X 40 DIN 912| 4| Extra.
E7| Bolt M8 X 25 DIN 912| 16|
E8| Cap- Washer M8| 4|
E9| Washer M8 DIN 988| 4|
E10| Washer M8 DIN 125- A| 4| Extra.
E11| Lock-Nut M8| 4| Extra.
E12| Slot-Nut M8| 4|

BOX F – Fanatec DD Mount (optional purchase) PROFILE KIT

# Part QTY Note
F1 120X40 UL Length=176mm 2
HARDWARE KIT

F2
F3| Front mount bracket A
Front mount bracket B| 2
2|
F4| Front mount spacer*| 12| Optional part.
F5| CSL spacer| 2| Only for CSL/GT DD.
F6| Bolt MS X 25 DIN 912| 12|
F7| Bolt M6 X 20 DIN 7380 -2| 4|
F8| Cap- Washer MS| 4|
F9| Washer MS DIN 988| 4|
F10| Slot-Nut MS| 4|
Disclaimer: for some entries on this page, we supply more than required as spare materials. Don t worry if you have some leftovers, this is intentional.

WHEEL DECK COMPATIBILIT

Accuforce 1/2
Wheel Deck Compatibility

HRS/Sim-Lab Servo Mount
Wheel Deck Compatibility

Simagic
Wheel Deck Compatibility

Asetek Forte/Prima
Wheel Deck Compatibility

Logitech
Wheel Deck Compatibility

Thrustmaster
Wheel Deck Compatibility

Fanatec
Wheel Deck Compatibility

MOZA
Wheel Deck Compatibility

Thrustmaster T818
Wheel Deck Compatibility

Customers Support

f you still have some questions regarding assembly of this product or about the manual itself,
please refer to our support department. They can be reached at
support@sim-lab.eu
Alternatively, we now have a Discord server where there are quite some experienced Sim-Lab customers hanging out.
They might just help you along if you ask them nicely 😉

www.sim-lab.eu/discord

If you feel like printing this manual, please consider the environment before doing so. For the best results, make sure you print at 100% scale without borders.

Product page on the Sim-Lab website:

QR Code

Logo

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals