SIM LAB X1-PRO Sim Racing Cockpit Instruction Manual
- June 13, 2024
- SIM-LAB
Table of Contents
SIM LAB X1-PRO Sim Racing Cockpit
BEFORE YOU START
Thank you for purchasing this Sim-Lab product! On the following pages, you
will find detailed instructions on assembly. This requires only a set of
simple tools and some of your time. Please check the bill of materials before
starting (pages 41-43) and make sure all the parts are delivered.
Since this is our most feature rich cockpit so far, for some parts of assembly
we urge you to get some assistance. Especially when turning over the base and
fitting the uprights, an extra pair of hands really does come in handy.
For current P1-X users who purchased an X1 upgrade kit, please skip to Page
12. Remove the P1-X uprights and possibly the side mount, and you can follow
along with this manual.
Inserting Slot-Nuts
You got excited, finished the build, put the caps on, but forgot to install one element. Do not worry. It happens to everyone. In this diagram, you can see how to insert a Slot-Nut directly into the slot from the side. You can also use one of your smaller Hex wrenches to help wiggle the Slot-Nut in place.
Tools needed
INSTALLATION INSTRUCTION
BOX A – X1-Pro Base PROFILE KIT
# | Part | QTY | Note |
---|---|---|---|
AP1 | 120X40 Length=1350mm | 2 | |
AP2 | 120X40 Length=500mm | 2 | |
AP3 | 40X40 Length=500mm | 2 |
HARDWARE KIT
A4| Corner bracket 40×40| 8|
A5| Corner bracket 40×40 cap| 8|
A6| Profile 120×40 end-cap| 4|
A7| Profile 40×40 end-cap| 4|
A8| Bolt M8 X 40 DIN 912| 4|
A9| Bolt M8 X 16 DIN 912| 16|
A10| Washer M8 DIN 125-A| 16|
A11| Washer M8 DIN 988| 4|
A12| Slot-Nut M8| 20|
BOX B – X1-Pro Add-On PROFILE KIT
# | Part | QTY | Note |
---|---|---|---|
BP1 | 120X80 Length=848mm | 1 | |
BP2 | 120X40 Length=260mm | 2 | To attach front mount. |
BP3 | 120X40 Length=950mm | 2 | Uprights. |
BP4 | 80X40 Length=1000mm | 2 |
HARDWARE KIT
B5| Upright LF| 1|
B6| Upright LR| 1|
B7| Upright RF| 1|
B8| Upright RR| 1|
B9| Sandwich plate 120X80| 2| B9.A Left / B9.B Right.
B10| Sandwich plate 120X40| 2|
#| Part| QTY| Note
---|---|---|---
B11| Front mount| 1|
B12| Front mount side plate| 2|
B13| Profile 120×40 end-cap| 6|
B14| Profile 80×40 end-cap| 4|
B15| Bolt M8 X 30 DIN 912| 8|
B16| Bolt M8 X 20 DIN 912| 12|
B17| Bolt M8 X 16 DIN 912| 20|
B18| Bolt M8 X 20 DIN 7991| 12| Countersunk.
B19| Cap-Washer M8| 8|
B20| Washer M8 DIN 125-A| 32|
B21| Washer M8 DIN 988| 8| Used with M8 cap-washers.
B22| Slot-Nut M8| 36|
B23| Cross cable binder block| 10|
Disclaimer: for some entries on this page, we supply more than required as
spare materials. Don’t worry if you have some leftovers, this is intentional.
BOX C – Sim Feet HARDWARE K
# | Part | QTY | Note |
---|---|---|---|
C1 | Foot support plate | 4 | |
C2 | Foot | 4 | Threaded ball-joint rod fitted. |
C3 | Bolt M8 X 25 DIN 912 | 8 | |
C4 | Washer M16 DIN 125-A | 8 | |
C5 | Nut M16 | 8 | 4 pre-fitted. |
C6 | Slot-Nut M8 | 8 |
BOX D – Pedal Deck PROFILE KIT
# | Part | QTY | Note |
---|---|---|---|
D1 | 160X40 Length=470mm | 1 | |
D2 | 80X40 Length=470mm | 1 |
HARDWARE KIT
D3| Pedal deck bracket| 2|
D4| Bolt M8 X 40 DIN 912| 6|
D5| Bolt M8 X 30 DIN 912| 8|
D6| Bolt M6 X 16 DIN 912| 12| Extra.
D7| Bolt M5 X 16 DIN 912| 12| Extra.
D8| Cap-Washer M8| 14|
D9| Washer M8 DIN 988| 14|
D10| Slot-Nut M8| 6|
D11| Slot-Nut M6| 12| Extra.
D12| Slot-Nut M5| 12| Extra.
BOX E – Floor HARDWARE KIT
# | Part | QTY | Note |
---|---|---|---|
E1 | Floor | 1 | |
E2 | Floor LEFT | 1 | |
E3 | Floor RIGHT | 1 | |
E4 | Floor support LEFT | 1 | |
E5 | Floor support RIGHT | 1 | |
E6 | Bolt M8 X 16 DIN 912 | 16 | |
E7 | Bolt M6 X 16 DIN 7991 | 21 | Countersunk. |
E8 | Washer M8 DIN 125-A | 16 | |
E9 | Slot-Nut M8 | 16 | |
E10 | Slot-Nut M6 | 21 |
BOX F – DDU Mount (optional installation, extension required) HARDWARE KIT
# | Part | QTY | Note |
---|---|---|---|
F1 | DDU mount bracket | 1 | |
F2 | DDU mount bridge | 1 | |
F3 | DDU mount holder LEFT | 1 | |
F4 | DDU mount holder RIGHT | 1 | |
F5 | Bolt M8 X 20 DIN 912 | 4 | |
F6 | Bolt M6 X 20 DIN 912 | 4 | |
F7 | Bolt M5 X 16 DIN 7991 | 4 | Countersunk. |
F8 | Cap-Washer M6 | 4 | |
F9 | Washer M8 DIN 125-A | 4 | |
F10 | Washer M6 DIN 125-A | 4 | |
F11 | Washer M5 DIN 125-A | 4 | |
F12 | Lock-Nut M6 | 4 | |
F13 | Lock-Nut M5 | 4 |
Disclaimer: for some entries on this page, we supply more than required as spare materials. Don’t worry if you have some leftovers, this is intentional.
BOX G – Wheel Deck (optional purchase) HARDWARE KIT
# | Part | QTY | Note |
---|---|---|---|
G1 | Wheel deck | 1 | |
G2 | Bolt M8 X 20 DIN 912 | 4 | |
G3 | Bolt M8 X 16 DIN 912 | 4 | Extra. |
G4 | Bolt M6 X 16 DIN 912 | 4 | Extra. |
G5 | Washer M8 DIN 125-A | 12 | Extra. |
G6 | Washer M6 DIN 125-A | 4 | Extra. |
G7 | Lock-Nut M8 | 4 | Extra. |
G8 | Lock-Nut M6 | 4 | Extra. |
BOX H – Side Mount (optional purchase) PROFILE KIT
# | Part | QTY | Note |
---|---|---|---|
HP1 | 80X40 Length=500mm | 1 | |
HP2 | 40X40 Length=350mm | 2 |
HARDWARE KIT
H3| Side mount bracket| 2|
H4| Corner bracket 40×40| 2|
H5| Corner bracket 40×40 cap| 2|
H6| Profile 80×40 end-cap| 2|
H7| Profile 40×40 end-cap| 2|
H8| Bolt M8 X 20 DIN 912| 8|
H9| Bolt M8 X 16 DIN 912| 4|
H10| Washer M8 DIN 125-A| 12|
H11| Slot-Nut M8| 12|
BOX I – Side Table (optional purchase, left or right version) PROFILE KIT
# | Part | QTY | Note |
---|---|---|---|
IP1 | 80X40 Length=1100mm | 1 | |
IP2 | 80X40 Length=200mm | 1 | |
I3 | Side table | 1 | |
I4 | Side table bracket LEFT | 1 | |
I5 | Side table bracket RIGHT | 1 | |
I6 | Corner bracket 40×40 | 3 | |
I7 | Corner bracket 40×40 cap | 3 | |
I8 | Profile 80×40 end-cap | 2 | |
I9 | Bolt M8 X 16 DIN 912 | 14 | |
I10 | Bolt M6 X 16 DIN 7991 | 6 | Countersunk. |
I11 | Washer M8 DIN 125-A | 14 | |
I12 | Slot-Nut M8 | 14 | |
I13 | Slot-Nut M6 | 3 | |
I14 | Lock-Nut M6 | 3 |
BOX J – Shelf (optional purchase) HARDWARE KIT
# | Part | QTY | Note |
---|---|---|---|
J1 | Shelf | 1 | Place your PC. |
J2 | Bolt M6 X 16 DIN 7991 | 4 | |
J3 | Slot-Nut M6 | 4 |
BOX K – Steering Wheel Extension (optional installation on wheel shaft) HARDWARE KIT
# | Part | QTY | Note |
---|---|---|---|
K1 | Steering wheel extension 120mm | 1 | Use with MIGE, CS, VRS etc. |
K2 | Bolt M5 X 20 DIN 912 | 12 | |
K3 | Lock-Nut M5 | 12 |
Disclaimer: for some entries on this page, we supply more than required as spare materials. Don’t worry if you have some leftovers, this is intentional.
Customer Support
If you still have some questions regarding assembly of this product or about
the manual itself, please refer to our support department. They can be reached
at support@sim-lab.eu
Alternatively, we now have a Discord server where there are quite some
experienced Sim-Lab customers hanging out. They might just help you along if
you ask them nicely 😉 www.sim-lab.eu/discord
If you feel like printing this manual, please consider the environment before
doing so. For the best results, make sure you print at 100% scale without
borders. Product page on the Sim-Lab website:
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>