TOPPING TP30D Headphone DAC Amplifier User Manual
- June 13, 2024
- TOPPING
Table of Contents
TP30D
User Manual
Contents list
| TP30D | x 1 |
|---|---|
| Remote control | x 1 |
| USB cable | x 1 |
| AC cable | x 1 |
| Bluetooth antenna | x 1 |
| Quick Start Guide | x 1 |
Note: You can download the driver on
https://www.toppingaudio.com/downloads
Attribute
| Measured | 22.2cm x 17.6cm x 4.8cm (Include protruding parts) |
|---|---|
| Weight | 1050g |
| Power input | 100-240VAC 50Hz/60Hz |
| Signal input | USB/BT/OPT/COAX/AES |
| Line Out output | XLR/RCA |
| Other connectors | 12V Trigger In(3.5mm jack) |
12V Trigger Out(3.5mm jack)
Display| 2inch LCD
Bluetooth range| >10 M
Input range
USB IN| PCM 44.1kHz-768kHz/16bit-32bit
DSD DSD64-DSD512 (Native) , DSD64-DSD256 (DoP)
---|---
COAX/OPT/AES IN| PCM 44.1kHz-192kHz/16bit-24bit
DSD DSD64 (DoP)
BT IN| AAC/SBC/APTX/APTX HD/APTX-Adaptive/LDAC
Front panel
Rear panel
- Screen
- Remote control receiver
- Menu Enter/exit the setup menu or return to the parent menu
- Input channel switching
- Home page switching
- Volume knob & User-defined button Rotate the knob: Adjust the volume. Press the knob: User-defined function. Please set it at [Setup Menu Advanced-Button].
- Right channel balanced XLR output
- Left channel balanced XLR output
- Left channel single-ended RCA output
- Right channel single-ended RCA output
- Coaxial SPDIF input
- Optical SPDIF input
- Bluetooth receiver
- USB input
- AES input
- 12V Trigger IN/OUT The 12V Trigger IN/OUT allows the TP30D to be activated by other devices or to activate other devices via a 3.5mm AUX cable. The connected device must be equipped with a 12V Trigger IN/OUT to use this feature. *Before using the Trigger IN function, you need to set the [Setup Menu On/Off trigger] to “12V”
- Power input（AC 100-240V 50Hz/60Hz）
- Power switch
Display
There are three types of home page displays: Normal, VU and FFT, which can be
switched by touching the button on the front panel or set in the menu [Setup
Menu – Display – Home].
The home page display in DAC mode and PRE mode will be slightly different.
[Setup menu-Advanced-DAC mode] PRE mode: Volume is adjustable.
DAC mode: TP30D keeps the maximum volume output and the volume is not
adjustable.
- VU Meter, FFT and Level meter monitor or reflect TP30D’s output level.
(They won’t be affected by the volume in PRE mode.)
TP30D has 3 output modes: SE, BAL and ALL [Setup menu- Output select].
In SE output mode, the VU Meter, FFT and Level meter reflect RCA output level.
In BAL/ALL mode, the output level of XLR is reflected.
*VU Meter, FFT and Level meter do not support DSD512.
Remote control
Connection
Connect to the input source
Support USB, Coaxial, Optical, Bluetooth, AES input.
Connect to amplifier or active speakers
Use XLR or RCA cables to connect to amplifiers or active speakers. In order to
avoid damage to your devices, please turn off the amplifier or active speakers
before you connect them to TP30D.
Operation
Power on & off / standby operation
- Power on & off: Press the power switch on the rear panel to turn TP30D on or off.
- Standby setting:
When it is working, press and hold the knob on the front panel to enter standby state and press to exit standby state when it is standby. Or you can press the standby button on remote control to enter or exit standby state.
Volume setting
- Mute and unmute: Press the mute button on the remote control to mute TP30D, press the mute button again or adjust the volume to exit mute state.
- Volume adjusting: You can turn the volume knob or press the and button on the remote control to adjust the volume.
Note that long pressing the and button on the remote control will quickly change the volume, so please be careful in order to protect your hearing.
Note: Volume is fixed to 0dB in DAC mode and volume adjusting is invalid in this mode. [Setup menu-Advanced-DAC mode]
Input channel switching
Touch the button on the front panel or press the or button on the remote control to switch the input circularly.
Output channel switching
Press the button on the remote control to switch the output in cycle. You could also switch the output channel by pressing the knob, but note that you need to set [Setup Menu-Advanced-Button] to “Output select”. (Default) Line Out
Setup Menu
Enter menu and change settings
The button on the front panel
Touch : Enter/exit the setup menu or return to the parent menu
Touch : Exit the setup menu
Rotate the knob: Choose setting item
Press the knob: Change the setting/OK/Enter the sub menu
The remote control
Setup menu
Display
1-1 Home
Choose home page
Normal (Default), VU, FFT
1-2 Brightness
Low, Medium (Default), High, Auto
Auto has the same brightness as Medium. The difference is that when there is no
operation after 30 seconds under Auto mode, the screen will be automatically
turned off and only display the current input. You can press any button to
light up the screen.
1-3 Classic VU 0dB
Set 0dB reference voltage for VU meter. For example, if set to +4dBu, when the
pointer swings to 0dB, the current output level of the D70 Pro OCTO is +4dBu.
+4dBu（Default）, +10dBu
1-4 Level meter
All on (Default), Normal page, FFT page, All off
Input select
USB (Default), OPT, COAX, AES, BT
Output mode
SE: only RCA output
BAL: only XLR output
ALL (Default): Both RCA and XLR can have output.
On/Off trigger
Signal（Default）: Input signal will trigger the device to turn on, but if the
current input is not connected or input signal is invalid in 1 minute, it will
automatically enter the standby state. Once having detected valid signal, it
will automatically return to working state.
12V: 12V signal will trigger the device to turn on. When TP30D’s Trigger In is
connected to another device’s 12V Trigger Out, TP30D’s on/standby state can be
controlled through this device. The TP30D will remain in standby state until
Trigger In detects the signal change from 0V to 12V. When changing back to 0V,
the TP30D will return to standby state.
Off: Disabled this function.
5.PCM filter
F-1: Fast roll off linear (Default)
F-2: Fast roll off minimum
F-3: Slow roll off linear
F-4: Slow roll off minimum
F-5: No over sampling
F-6: Ultra-fast roll off linear
F-7: Ultra-fast roll off minimum
F-8: Brick-wall linear
F-9: Brick-wall minimum
Advanced
Channel balance
Setting range: C (Balance), L+0.5~9.5dB or R+0.5~9.5dB. (Default: C)
When using the knob, press the knob to enter the setting, rotate the knob to set the parameter, and press the knob again to exit the setting.
Output level
Maximum output level at 0dBFS
4V（Default）, 5V
DAC mode
PRE (Default): Volume is adjustable.
DAC: Keep the maximum volume output and the volume is not adjustable.
Bluetooth
Enabled (Default), Disabled
Remote
Enabled (Default), Disabled
Button
Customize the function of the press knob.
Output select (Default), Home select, Brightness select, Dim the screen,
Filter select, Mute, Input select
When using the knob, press the knob to enter the setting, rotate the knob to set the number, and press the knob again to exit the setting.
Language
English,
Scan the QR code on the right for the video.
https://dl.topping.audio/tutorial/d70p_language_switch.zip
Factory reset
Select factory reset will have a pop-up, select Yes/No (blue for selected),
then press the middle button on the remote or the front-panel knob to confirm.
Trouble shooting
| Phenomenon | Cause | Solution |
|---|---|---|
| No sound | Wrong input was selected | Select the correct input |
| Wrong output was selected | Select the correct output | |
| Incorrect cable connections | Check and reconnect | |
| Sound is muted | Turn up the audio | |
| Audio source no output | Adjust or check it | |
| USB did not recognize | USB cable did not connect properly | Check or change the |
cable
PC’s USB port damaged| Change another port
The PC does not work| Check or try with another PC
The OTG function of the phone is not enabled| Enable OTG function
USB input, no sound| Too low volume on PC| Adjust volume
TP3OD is not selected as the output device on the PC| Set the TP3OD as the
default output device
Cannot pair TP3OD Bluetooth| Bluetooth is disabled on TP3OD| Enable Bluetooth
in the setup menu [Setup menu-Advanced-Bluetooth]
TP3ODE is already connected to other Bluetooth device| Let TP30D enter pairing
mode first.
Weak signal due to long distance| Take the device closer to TP30D and connect
again
Bluetooth input, no sound| Too low volume on phone| Adjust volume
DAC abnormal| DAC abnormal| Do not connect the TP3OD to any
other devices, unplug and re-plug the power cable and reboot the unit.
DIR abnormal| DIR abnormal
PN voltage abnormal/ low /high| PN voltage abnormal/low /high
5V voltage abnormal/ low /high| 5V voltage abnormal/low /high
FFT module abnormal| FFT module abnormal
If you still have problems or questions, please contact us (service@tpdz.net)
Specifications
TP30D DAC parameters (LineOut/USB In@96kHz)
| RCA| XLR
THD+N @A-wt| <0.00008% @1kHz| <0.00007% @1kHz
THD @No-wt 90kBw| <0.0004% @20-20kHz| <0.0002% @20-20kHz
SNR @A-wt| 127dB @1kHz| 133dB @1kHz
Dynamic Range @A-wt| 127dB @1kHz| 133dB @1kHz
Frequency Response| 20Hz-20kHz(t0.05dB)| 20Hz-20kHz(t0.05dB)
20Hz-40kHz(t0.2dB)| 20Hz-40kHz(±0.2dB)
Output Level| 2.1Vrms @OdBFS(4V Mode)| 4.2Vrms @OdBFS(4V Mode)
2.6Vrms @OdBFS(5V Mode)| 5.2Vrms @OdBFS(5V Mode)
Noise @A-wt| <1.0uVrms| <1.0uVrms
Channel Crosstalk| -124dB @1 kHz| -149dB @1 kHz
Channel Balance| 0.3dB| 0.3dB
Output Impedance| 500| 1000
*Note: The above data is the result of the test in TOPPING laboratory under AC220V 50Hz condition.
Precautions
- Do not keep the unit in a hot, humid environment or hit the unit strongly.
- Opening the case instantly voids the warranty!
- Indoor use only.
- Topping accepts no liability for any loss or damage arising directly or indirectly from the failure of TP30D.
- For improvement purpose, specifications subject to changes without prior notice.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>