SIM LAB PP A5 Push Pull Shifter Instruction Manual
- June 13, 2024
- SIM-LAB
Table of Contents
SIM LAB PP A5 Push Pull Shifter
BEFORE YOU START
Thank you for your purchase. In this manual we will provide you with the means
to get started using your new shifter!
Allowing you to shift rally style, you always know where your shifter is in
relation to your wheel. Thanks to the quick disconnect lever it is easy to
make adjustments. The quick disconnect lever allows for a very rigid solution
while really locking down your preferred config
PUSH/PULL SHIFTER
Features:
Rally style shifting
Support for different hardware
Adjustable in length and angle
Aluminum construction
Hall-sensor activated
Carbon fiber paddles
Quick disconnect lever
Preparation
Depending on your hardware; Fanatec (A3) or Simucube/ALPHA/MIGE (A4), a
different mounting plate must be fitted.
Mounting such a plate is very straightforward and uses four countersunk bolts.
Installation
The installation of the Push/Pull Shifter (PPS) is fairly straight forward.
Loosen existing bolts on your motor and mount, use these to attach the adapter
plate to your front mount.
X1-Pro owners can use the accessory mounting holes on the X1-Pro front mount.
For Fanatec users, appropriate bolts (A9) are supplied.
Configuration
Depending on your setup, there might some configuration needed to make the PPS fit your setup. We included 3 different ams to be able to adjust the positioning of the paddle in relation to your wheel.
If arms (F) fitted out of the box need to be swapped, first rotate the lever
(L) upwards and loosen the nut (N). Now you can disconnect the complete
shifter body along with the arms and swap them with your preferred arms
(A5/6).
With the new arms in place, some tweaking is still possible to suit your
needs. When re-assembling, don’t tighten the nut (N) completely, the lever (L)
will clamp down on the system to tighten everything. When there is still play
after you have clamped down the lever, release the lever and adjust the
tension of the nut and try again.
There are different means of adjustment possible, depending on the part.
Most adjustments can be made loosening the bolts which hold the arms and rotating the locking lever upwards. Be sure to tighten bolts securely and double check after the first use if they are still tight. Here is how we achieved our setup to work with a deep dish wheel.
Initial calibration
Press and hold the calibration button (C) until its LED starts blinking. Now the unit is in calibration mode. Shift up (pull) and down (push) a couple of times. When you are done, press the calibration button (C) one last time. Now the device has been calibrated and ready for use.
Bill of materials
IN THE BOX
# | Part | QTY | Note |
---|---|---|---|
A1 | Push/Pull Shifter | 1 | |
A2 | USB-micro cable | 1 | |
A3 | Fanatec mount | 1 | |
A4 | Simucube/Alpha/MIGE mount | 1 | |
A5 | Mount Arm M75-125 | 2 | |
A6 | Mount Arm M185-125 | 2 | |
A7 | Bolt M8 X 35 DIN 912 | 2 | |
A8 | Bolt M4 X 10 DIN 7991 | 4 | |
A9 | Bolt M6 X 12 DIN 7380 | 2 | Use to mount unit to Fanatec. |
A10 | Bolt M4 X 10 DIN 7380 | 2 | Use to mount paddle. |
A11 | Lock-Nut M8 | 2 | |
A12 | Washer M8 DIN 125-A | 2 | To use with A8 and/or A11. |
A13 | Toolkit | 1 | Allen keys 2.5, 4 and 5mm. |
More information
If you still have some questions regarding assembly of this product or about
the manual itself, please refer to our support department. They can be reached
at: support@sim-lab.eu
Alternatively, we now have Discord servers where you can hang out or ask for
help.
Customer Service
www.sim-lab.eu/discord
Product page on the
Sim-Lab website:
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>