SIM-LAB Pedal Slider Baseplate 2.11 User Guide
- June 13, 2024
- SIM-LAB
Table of Contents
PEDAL SLIDER BASEPLATE
VERSION 2.11
Last updated: 21-06-2023
INSTRUCTION MANUAL
BEFORE YOU START:
Thank you for purchasing this Sim-Lab product! On the following pages, you
will find detailed instructions on assembly. This requires only a set of
simple tools and some of your time. Please check the bill of materials before
starting (page 14) and make sure all the parts are delivered.
Compatibility:
This accessory is compatible with more than one of our products. The main two
ways of attaching our (seat) sliders to our cockpits are either directly on
profile or on a pedal deck. This manual shows both of these options using a
P1-X pedal deck (profile) and a GT1-EVO pedal deck (plate). However,
compatibility of this accessory is not limited to these cockpits. Please see
the product page for more information on compatibility.
Inserting Slot-Nuts:
You got excited, finished the build, put the caps on, but forgot to install
one element. Do not worry. It happens to everyone. In this diagram, you can
see how to insert a Slot-Nut directly into the slot from the side. You can
also use one of your smaller Hex wrenches to help wiggle the Slot-Nut in
place. Tools needed: Going to install the optional seat sliders? Please
skip to page 5.
Going to install the optional heel rest? Please skip
to page 11.
Using a GT1-EVO style pedal deck? Please skip to
page 12.
**Seat
Slider Handle***
For the handle to fit snugly between the sliders, it needs to be widened a bit
by bending it until it seats properly. Please review our seat slider
installation video for reference.
PEDAL BASE PLATE
| # | Part | QTY | Note |
|---|---|---|---|
| A1 | Pedal base plate | 1 | New as per February 2023. |
| A2 | Bolt M8 X 16 DIN 912 | 4 | |
| A3 | Bolt M8 X 12 DIN 912 | 4 | |
| A4 | Bolt M6 X 20 DIN 912 | 12 | |
| A5 | Bolt M5 X 25 DIN 912 | 12 | |
| A6 | Bolt M8 X 20 DIN 7991 | 4 | Countersunk |
| A7 | Washer M8 DIN 125-A | 8 | |
| A8 | Spacer male/female M8 X 15 | 4 | |
| A9 | Slot-Nut M8 | 6 | |
| A10 | Lock-Nut M8 | 10 | |
| A11 | Lock-Nut M6 | 12 | |
| A12 | Lock-Nut M5 | 12 |
SEAT SLIDER (optional purchase)
| # | Part | QTY | Note |
|---|---|---|---|
| B1 | Seat slider LEFT | 1 | |
| B2 | Seat slider RIGHT | 1 | |
| B3 | Seat slider handle | 1 |
HEEL REST (optional purchase)
HEEL REST (optional purchase)
C1| Heel rest| 1|
C2| Bolt M6 X 45 DIN 7991| 4| Countersunk
C3| Bolt M6 X 35 DIN 7991| 4| Countersunk
C4| Plastic sleeve M8 X 20| 4|
C5| Plastic sleeve M8 X 10| 4|
C6| Slot-Nut M6| 4|
C7| Lock-Nut M6| 4|
Disclaimer: for some entries on this list, we supply more than required as
spare materials. Don’t worry if you have some leftovers, this is intentional.
If you
still have some questions regarding assembly of this product or about the
manual itself, please refer to our support department. They can be reached at
[email protected]
Alternatively, we now have a Discord server where there are quite some
experienced Sim-Lab customers hanging out. They might just help you along if
you ask them nicely 😉
www.sim-lab.eu/discord
If you feel like printing this manual, please consider the environment before
doing so. For the best results, make sure you print at 100% scale without
borders.
Product page on the Sim-Lab website:| Seat Slider installation on
YouTube:
---|---
|
https://sim-lab.eu/pedal-slider-baseplate| https://youtu.be/dRQFK6UHCIM