StarTech com 12S-CABLE-LACING-BAR 1U Horizontal Cable Lacing Bar User Guide
- June 15, 2024
- StarTech com
Table of Contents
Quick-Start Guide
1U Adjustable Cable Lacing Bar
Product Diagram
12S-CABLE-LACING-BAR
12S-CABLE-LACING-BAR 1U Horizontal Cable Lacing Bar
*Product may vary from
image
| Component| Function
---|---|---
1| Lacing Bar| • Main body provides structural rigidity to support the cables
2| Lacing Points| • Allow cables to be laced or tied in an organized way by
passing Hook and Loop Ties or Plastic Ties through the Lacing Points
3| Adjustable Depth Holes| • Allow to change the depth of the Cable Lacing Bar
inside the Rack
• Two M4x8 Screws on either side of the Lacing Bar secure it to the Mounting
Brackets
4| Mounting Brackets| • Allow to attach the Cable Lacing Bar to the Mounting
Posts of a Rack .
Product Information
For the latest manuals, product information, technical specifications, and declarations of conformance, please visit: www.StarTech.com/12S-CABLE-LACING- BAR
Requirements
- Phillips Head Screwdriver
- Hook and Loop Ties or Plastic Ties
- (Optional) Cage Nut Tool
Note: M6 Screws and Cage Nuts are provided for convenience. Alternative mounting hardware may be needed from the Rack’s manufacturer.
Package Contents
- Lacing Shelf x 1
- Mounting Kit x 1
- M6 Screws x 4
- M6 Cage Nuts x 4
- M6 Plastic Washers x 4
- M4 Screws x 4
- Quick-Start Guide x1
Installation
Assemble and Mount the Cable Lacing Bar
-
Determine the Mounting Depth needed according to your application.
-
On one side of the Lacing Bar, align its Mounting Holes with the Adjustable Depth Holes on the Mounting Brackets that correspond to the required depth from Step 1.
-
Insert the M4 Screws (x 2) through the Adjustable Depth Holes and into the Lacing Bar. Use a Phillips Head Screwdriver to tighten the screws securely.
-
Repeat Step 2 and Step 3 on the opposite side of the Lacing Bar to complete the assembly.
-
Find a suitable location on the Rack to mount the Cable Lacing Bar. The Cable Lacing Bar requires 1U of Mounting Space.
-
Follow the Rack’s Manufacturer Instructions to install the included M6 Cage Nuts on the Mounting Posts of the Rack.
Note: If available, use a Cage Nut Tool or your preferred installation method to install the Cage Nuts -
Place the Cable Lacing Bar onto the Rack and align the Mounting Brackets with the Mounting Posts of the Rack.
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support. -
Insert the M6 Screws (x 4) through the Plastic Washers, the Mounting Brackets,and into the Mounting Posts of the Rack. Ensure the M6 Screws are appropriately tightened using a Phillips Head Screwdriver.
Usage
Cable Management
-
Plan the cable routing by identifying the path each cable should take from its source to its destination. Is recommended to group cables based on their function or destination.
-
Gather cables that follow the same path or are related to a specific component. Use Hook and Loop Ties or Plastic Ties to create Cable Bundles.
Note: Leave a bit of slack in each Cable Bundle to accommodate any future changes oradjustments without causing strain on the cables. -
Place the Cable Bundles at the Left and Right of the Cable Lacing Bar depending on the setup. Use the Lacing Points to pass through Hook and Loop Ties or Plastic
Ties to secure the Cable Bundles in place. -
(Optional) Consider labeling each Cable or Cable Bundle for easier identification.
Regulatory Compliance
Use of Trademarks, Registered Trademarks, and other Protected Names and
Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of thirdparty companies not related in any way
to StarTech.com. Where they occur these references are
for illustrative purposes only and do not represent an endorsement of a
product or service by StarTech.com, or an endorsement
of the product(s) to which this manual applies by the third-party company in
question. StarTech.com hereby acknowledges that all
trademarks, registered trademarks, service marks, and other protected names
and/or symbols contained in this manual and related documents are the property
of their respective holders.
PHILLIPS® is a registered trademark of Phillips Screw Company in the United
States or other countries.
Warranty Information
This product is backed by a two-year warranty.
For further information on product warranty terms and conditions, please refer
to www.startech.com/warranty.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd.
and StarTech.com USA LLP (or their officers, directors,
employees or agents) for any damages (whether direct or indirect, special,
punitive, incidental, consequential, or otherwise), loss of profits, loss of
business, or any pecuniary loss, arising out of or related to the use of the
product exceed the actual price paid for the product. Some states do not allow
the exclusion or limitation of incidental or consequential damages. If such
laws apply, the limitations or exclusions contained in this statement may not
apply to you.
Safety Measures
Assemble this product according to the instructions. Read the entire manual
and ensure the instructions are fully understood before assembling and/or
using this product.
www.quefairedemesdechets.fr
StarTech.com Ltd.
45 Artisans Crescent
London, Ontario
N5V 5E9
Canada| StarTech.com LLP
4490 South Hamilton
Road
Groveport, Ohio
43125
U.S.A.| StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Road
Brackmills,
Northampton
NN4 7BW
United Kingdom| StarTech.com Ltd.
Siriusdreef 17-27
2132 WT Hoofddorp
The Netherlands| FR: startech.com/fr
DE: startech.com/de
ES: startech.com/es
NL: startech.com/nl
IT: startech.com/it
JP: startech.com/jp
---|---|---|---|---
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and
more,
visit www.startech.com/support
Manual Revision: August 3, 2023 4:22 PM
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>