StarTech com 5G4AINDRM-USB-A-HUB 4 Port Managed USB Hub User Guide
- June 13, 2024
- StarTech com
Table of Contents
tarTech com 5G4AINDRM-USB-A-HUB 4 Port Managed USB Hub User Guide
4-Port Managed Industrial USB Hub – USB 3.2 Gen 1 5Gbps, ESD Protection
Product ID
5G4AINDRM-USB-A-HUB
Product Diagram
USB Hub Management Software
To utilize the management features of this USB Hub, it is necessary to download and install the software. To download the USB Hub Management Software, as well as the accompanying documentation, please visit:
www.StarTech.com/5G4AINDRM-USB-A-HUB
Requirements
- Host Computer
- USB-A Port
- 7-48V DC Power Source
- Flat head Screwdriver
- (Optional) Phillips head Screwdriver (for DIN Rail Mounting)
For the latest drivers, manuals, product information, technical
specifications, and declarations of conformance, please visit:
www.StarTech.com/5G4AINDRM-USB-A-HUB
| Component | Function |
|---|
1
|
DC 2-Wire Terminal Block Power Input
| • Connect a +7~48 V DC Power Source
• 30W or Higher Recommended for Maximum Power Performance
2
|
Power LED
| • Indicates if the USB Hub is receiving power
• Solid Green – Receiving Power
• Off – Not Receiving Power
3|
USB-B Host Port
| • Connect to a USB-A Port on a Host Computer
• USB 3.2 Gen 1 (5 Gbps)
4
|
3x USB-A Data/Charge Ports
| • Connect USB Peripherals
• USB 3.2 Gen 1 (5 Gbps)
• Backward compatible with USB 2.0 (480Mbps)
• BC 1.2 for up to 5 V/1.5 A (7.5 W) Charging
5
|
USB-A Data Port
| • Connect USB Peripherals
• USB 3.2 Gen 1 (5 Gbps)
• Not Compatible with USB 2.0 (480Mbps)
• Supports up to 5 V/0.9 A (4.5 W) Charging
6
|
4x USB Port Status LEDs
| • Indicates if the Corresponding USB-A Data/Charge Port is Enabled or Disabled
• Solid Green – USB-A Data/Charge Port Enabled
• Off – USB-A Data/Charge Port Disabled
• Enable/Disable USB-A Data/Charge Ports within the USB Hub Management Software
7| Mounting Brackets| • Mount the USB Hub to a wall or the side/underside of a Desk
Package Contents
- USB Hub x 1
- 6 ft [1.8 m] USB-A to USB-B Cable x 1
- Terminal Block Connector (Attached) x 1
- DIN Rail Mounting Bracket (with Mounting Screws) x 1
- Quick-Start Guide x 1
Installation
Note: Connect the Power Source after all the other installation steps have been completed.
Connect the USB Ports
- Connect up to four USB peripherals to the USB-A Data/Charge Ports, located on the
USB Hub.
- Connect a USB-A Port on the Host Computer to the USB-B Host Port , located on the USB Hub, using the included USB-A to USB-B Cable.
- The Computer will automatically detect the
Power the Hub
Power the Hub Using the 2-Wire Terminal Block
- Remove the Terminal Block Connector Housing from the USB Hub’s Casing.
- Loosen the screws for the Terminals located on the Terminal Block Connector , using a Flat Head Screwdriver.
- Connect the Positive and Negative Wires from the 7-48V DC Power Source (not included) to the Terminals on the Terminal Block Connector.
Note: Ensure the polarity of the power input is correctly matched with the DC 2-Wire Terminal Block Pins to function properly and to prevent damage to the USB Hub and any connected peripherals.
- Insert the Terminal Block Connector Housing back into USB Hub.
Use of Trademarks, Registered Trademarks, and other Protected Names and
Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third- party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.
Warranty Information
This product is backed by a 2-year warranty.
For further information on product warranty terms and conditions, please refer
to www.startech.com/warranty.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.
DIN Rail Mounting
This USB Hub includes a DIN Rail Bracket that can be used to vertically or horizontally mount the USB Hub to a DIN Rail. To install the DIN Rail Bracket on the USB Hub :
- Align the Din Rail Bracket with the DIN Rail Mounting Holes, located on at the back of the USB Hub.
Note: The USB Hub features two sets of Vertical DIN Rail Mounting Holes, and one set of Horizontal DIN Rail Mounting Holes. Any set may be used, depending upon the desired configuration.
- Insert the Mounting Screws (x 2) through the DIN Rail Brackets , and into the USB Hub.
Using a Phillips Head Screwdriver tighten the Mounting Screws. Be careful not to over-tighten the Mounting Screws
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>