StarTech com TV-WALL-MOUNT-65FS Articulating TV Wall Mount User Manual

StarTech com TV-WALL-MOUNT-65FS Articulating TV Wall Mount

Compliance Statements

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

• This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question. Regardless of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby acknowledges that all trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.
• PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other countries.

Safety Statements

Safety Measures

• Product installation and/or mounting should be completed by a certified professional as per the local safety and building code guidelines.

Warning Statements

• Assemble this product according to the instructions.
• Read the entire manual and ensure the instructions are fully understood before assembling and/or using this product.
• Do not exceed the weight capacity of this product. Overloading this product might result in injury or property damage.
• Weight capacity of the mount: 99 lb (45 kg).
• Do not allow children to climb on this product, or use this product without proper supervision.
• This product is intended for indoor use only and should not be used outdoors.
• Do not over-tighten the screws. If any resistance is encountered, stop tightening.
• Assembling this product is a two-person task. Do not attempt to assemble this product and install equipment without assistance.
• Before adding equipment to this product, ensure the product has been properly assembled, and that the product can support the weight of the added equipment.
• Make sure all of the equipment has been properly secured before adjusting this product.

Product Diagram

Product Dimensions

Front View

Top View

Side View

Product Information

Requirements
For the latest product information, technical specifications, manuals, and Declarations of Conformance, please visit www.StarTech.com/TV-WALL-MOUNT- 65FS.

TV

• Maximum weight of 99 lb (45 kg)
• Maximum display size of 65”
• Compatible VESA mounting hole pattern
• VESA Plate: 200×100, 200×200, 200×300, 200×400, 300×200, 300×300, 400×200, 400×300, and 400×400

Tools

• Phillips head screwdriver

Package Contents

Installation

Remove the Decorative Covers

1. Before installing the Wall Mount Assembly, remove the two Decorative Covers from the Wall Mount Plate.
   • While Pressing Both Sides at the Bottom of the Upper Decorative Cover, slide Up from the Wall Mount Plate to remove it. (Figure 1)
   • While Pressing Both Sides at the Top of the Lower Decorative Cover, slide Down from Wall Mount Assembly to remove it. (Figure 1)

Mounting the Wall Mount Assembly

Warning! The Wall Mount Assembly is designed to be installed on a wood stud, solid concrete, or cinder block wall. The wall structure should be capable of supporting at least four times the weight of the mounted equipment.
The included mounting hardware may not be adequate for installation on different wall types not indicated here. Always consult a construction professional before installing the Wall Mount Assembly. Failure to do so may result in personal injury or equipment damage.
Note: Before mounting the Wall Mount Assembly, review the Cable Management section on page 13. It may be advantageous for the installation to pre-route the TV Cables in advance.
For stud wall installations, consider the 1.02 in (26 mm) between holes indicated in Figure 2. If the stud is too narrow, the edges of the stud may split and won’t support the weight.

The following tools are needed

• Stud finder. For stud wall installations.
• Bubble level.
• Pencil
• Hammer. For concrete wall installations.
• Power drill.
• 1/2 in (13 mm) wrench.
• 15/64 in (~6 mm) wood drill bit. Minimum 2.5 in (65 mm) long.
• A 15/32 in (~12 mm) concrete drill bit. Minimum 2.5 in (65 mm) long.

Fasten the Wall Mount Assembly to a Stud Wall

1. Using the Wall Stud Finder, find an available Stud to fix the Wall Mount Assembly.
   Note: Ensure there are no obstructions to prevent the Wall Mount Assembly from reaching the full range of motion.

2. Place the Mounting Template on the wall. Center the Mounting Template on the middle of the Stud. Use the Bubble Level to ensure the Mounting Template is vertical.

3. Use the Pencil to perforate the Green Markings on the Mounting Template and mark the locations for drilling. The X is the center of the hole. (Figure 2)

4. Use the reference marks from Step 3 to drill five 2.5 in (65 mm) deep holes on the Stud using a Power Drill and the 15/64 Drill Bit.

5. Insert one of the Wall Mounting Screws in the Top drilled hole and use the 1/2 in (13 mm) Wrench to tighten the screw. Leave a ~ 0.16 in (4 mm) Gap between the wall and the head of the screw.

6. Hang the Wall Mount Assembly onto the Wall Mounting Screw from Step 5 using the Key Hole at the top of the Wall Mount Assembly.

7. Use the Bubble Level to ensure the Wall Mount Assembly is Vertical to the wall.

8. Insert the rest of the Wall Mounting Screws (x 4) through the Wall Mount Plate. Tighten all the Wall Mounting Screws (x 5) with the 1/2 in (13 mm) Wrench to fasten the Wall Mount Assembly to the Stud. (Figure 3)

Fasten the Wall Mount Assembly to a Concrete Wall

1. Determine a suitable location to mount the Wall Mount Assembly.
   Note: Ensure there are no obstructions to prevent the Wall Mount Assembly from reaching the full range of motion.

2. Place the Mounting Template on the wall and use the Bubble Level to ensure the Mounting Template is vertical.

3. Use the Pencil to perforate the Red Markings on the Mounting Template and mark the locations for drilling. The X is the center of the hole. (Figure 4)

4. Use the reference marks from Step 3 to drill five 2.5 in (65 mm) deep holes on the Stud using a Power Drill and the 15/32 Drill Bit.

5. Insert the Concrete Anchors into the newly drilled holes with the help of a Hammer.

6. Insert one of the Wall Mounting Screws in the Top drilled hole and use the 1/2 in (13 mm) Wrench to tighten the screw. Leave a ~ 0.16 in (4 mm) Gap between the wall and the head of the screw.

7. Hang the Wall Mount Assembly onto the Wall Mounting Screw from Step 5 using the Key Hole at the top of the Wall Mount Assembly.

8. Use the Bubble Level to ensure the Wall Mount Assembly is Vertical to the wall.

9. Insert the rest of the Wall Mounting Screws (x 6) through the Wall Mount Plate. Tighten all the Wall Mounting Screws (x 7) with the 1/2 in (13 mm) Wrench to fasten the Wall Mount Assembly to the Wall. (Figure 5)

Install the Decorative Covers

1. Attach the Upper and Lower Decorative Covers by sliding each Decorative Cover along the Wall Mount Plate until the Tabs of each Decorative Cover snap into place. (Figure 6)

Mount the TV

1. Carefully place the TV on a protective/soft surface with the VESA Mounting Points at the back of the TV facing Up.

2. Remove any pre-installed hardware at the VESA Mounting Points (e.g. screws or covers) at the back of the TV. Consult the TV’s Manual and remove them as instructed.
   Note: Ensure you only remove the screws (x 4) of the VESA Mounting Points. Do not remove any of the screws of the TV’s structural assembly.

3. Place the Flat Washers (x 4) over each VESA Mounting Hole (x 4).

4. Place the Vertical Brackets (x 2) over the Flat Washers parallel to one another. The Hooks on the Vertical Brackets must be pointing towards the Bottom of the TV. (Figure 7)

5. Insert the appropriately sized M-Type Screws (x 4) (e.g., M4 x 12 mm Screws) through the Vertical Brackets, the Flat Washers, and the VESA Mounting Holes at the back of the TV. (Figure 7)

6. Tighten the M-Type Screws (x 4) with a Phillips Head Screwdriver until each M-Type Screw is flush with the surface of the Vertical Bracket (x 2).

Warning! Do not overtighten the M-Type Screws. If you encounter any unexpected resistance as you are fastening them, immediately stop and attempt to use a different length of M-Type Screw.

Attach a TV to the Wall Mount Assembly
Warning! Ensure the weight of the TV does not exceed the weight capacity of this product. Exceeding the weight capacity may result in personal injury, damage to the product, attached equipment, or the mounting surface. This product can support the following weight: Up to 99 lb (44.9 kg). Attaching the TV is a two-person Job. Do not attempt to complete this task by yourself.

1. Lift and Hang the TV on the Wall Mount Assembly. (Figure 8)
   Note: Align the top hooks of the Vertical Brackets with the top rails of the Wall Mount Assembly.

2. Lock the Vertical Brackets in place by folding up the Latch on the back of each Vertical Bracket and screw in the Vertical Bracket Screw (x 2) using a Phillips Head Screwdriver. (Figure 9)

Cable Management

1. Route the TV Cables through the Cable Management Attachments (x 2) on either side of the Wall Mount Assembly and through the Lower Decorative Cover. (Figure 10)

Note: It may be necessary to remove the Cable Management Attachments if the TV Cables do not fit.
To remove the Cable Management Attachments, use a Phillips Head Screwdriver to remove the Phillips Head Screws (x 4) of each Cable Management Attachment (x 4). After routing the TV Cables, install the Cable Management Attachments one at a time and secure them with their respective Phillips Head Screws (x 4).

Operation

Adjust the TV
Caution! Ensure that your fingers are clear from all moving parts and pinch points while adjusting the TV.

Adjust the Tilt

1. Loosen the Tilt Adjustment Screws located on the Wall Mount Assembly using the 6 mm Hex Key.
2. Adjust the TV by Tilting it to your desired viewing angle.
3. While Supporting the Weight of the TV, Tighten the Tilt Adjustment Screws located on the Wall Mount Assembly using the 6 mm Hex Key. (Figure 11)

Adjust the Swivel

1. Loosen or Tighten the Swivel Adjustment Screw on the Wall Mount Assembly using the 6 mm Hex Key. (Figure 12)

Warranty Information

• This product is backed by a five-year warranty. For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.

Limitation of Liability

• In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.
• Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.

Hard-to-find made easy. At StarTech.com, that isn’t a slogan.
It’s a promise.

• StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions.
• We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to the products you need in no time.
• Visit www.startech.com for complete information on all StarTech.com products and to access exclusive resources and time-saving tools.
• StarTech.com is an ISO 9001 registered manufacturer of connectivity and technology parts since 1985 with operations around the world.

Reviews

• Share your experiences using StarTech.com products, including product applications and setup, what you love about the products, and areas for improvement.

CONTACT

StarTech.com Ltd.

• 45 Artisans
• Crescent
• London, Ontario
• N5V 5E9
• Canada

StarTech.com LLP

• 4490 South
• Hamilton Road
• Groveport, Ohio
• 43125
• U.S.A.

StarTech.com Ltd.

• Unit B, Pinnacle 15
• Gowerton Road
• Brackmills,
• Northampton
• NN4 7BW
• United Kingdom

StarTech.com Ltd.

• Siriusdreef 17-27
• 2132 WT
• Hoofddorp
• The Netherlands

FR: fr.startech.com
DE: de.startech.com

ES: es.startech.com
NL: nl.startech.com

IT: it.startech.com
JP: jp.startech.com

To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support.

References

• Corner Articulating TV Wall Mount, VESA - TV Mounts | Display Mounts and Ergonomics | StarTech.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>