FORTIN 72051 Nissan Micra 2015 Standard Key Remote Starters and Alarm Systems Installation Guide

FORTIN 72051 Nissan Micra 2015 Standard Key Remote Starters and Alarm Systems Installation Guide

Vehicle functions supported in this diagram (functional if equipped) |

VEHICLE| Immobilizer bypass
Micra| T-Harness available (sold separately
2015-2018| Lock
.| Arm
.| Unlock
.| Disarm
.| Parking Lights
.| Horn
.| Tachometer
.| Door Status
.| Trunk Status
.| Hood Status
.| Hand-Brake Status
.| Foot-Brake Status
| BYPASS FIRMWARE VERSION| To add the firmware version and the options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately
---|---|---
72.[48]
NISSAN/INFINITI MINIMUM
| IF THE VEHICLE IS NOT EQUIPPED WITH FUNCTIONAL HOOD PIN:| A11| | Hood trigger (Output Status).
---|---|---|---|---
| Program remote starter option:| FUNCTION| MODE| DESCRIPTION).
---|---|---|---|---
31| 4| +) Parking Light (E1) (+) Accessory (E2)
32| 3| DK.Blue (GWR) Shut Down After
---|---|---

MANDATORY INSTALL

**HOOD PIN

HOOD STATUS : THE HOOD PIN SWITCH (INCLUDED)MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF
A11

SECURITY STICKER**

WARNING
Included

Notice: the installation of safety elements are mandatory. The hood pin and the sticker are essential security elements and must be installed.

DESCRIPTION

1. Ignition harness
2. Transponder connector
3. Driver kick panel
4. OBDII
5. BCM
6. At steering column * Test wire before connecting

WIRING CONNECTION

1. Ignition harness White connector – Back view

2. Transponder connector White connector – Back view

3. Driver kick panel – Grey connector – Back view

4. OBDII Front view

5. BCM White connector – Back view

6. Back vue. 15-pin Black connector at BCM.

KEY BYPASS PROGRAMMING PROCEDURE 1/2

1. Press and hold the programming button: Connect the 6-PIN Main hamess (White connector
   The Blue, Red, Yellow and Blue & Red LEDs wil alternatively illuminate
   

2. Release the programming button when the LED is YELLOW
   If the LED is not solid YELLOW disconnect the 6-Pin connector (Main-Harness) and go back to step 1.
   

3. Insert the required remaining connectors.
   

4. Press and release the programming button two times (2x).] The YELLOW LED will alternate between 2x flashes and a pause
   Wait until the YELLOW LED tums ON
   

5. Turn the key to the Ignition ON/RUN position
   The RED LED will turns ON
   If the YELLOW and RED LED’s are not solid, remove the key and go back to step

6. 
   Repeat this step until the RED and YELLOW LED’s are solid.
   Wait for the BLUE LE flash rapidly
   

7. Turn the key to the OFF position.

   ---

8. Remove the key from the ignition barrel

9. Turn the key to the Ignition ON/RUN position
   The BLUE, YELLOW and RED LED’s wil rapidly alterate.
   When the YELLOW LED begins flash rapidly: Key bypass programmed
   

10. Turn the key to the OFF position.

The module is now programmed.
Use the remote of the remote starter or security system to test all of the supported features to ensure proper programming.

REMOTE STARTER PROGRAMMING PROCEDURE

REFER TO THE QUICK INSTALL GUIDE INCLUDED WITH THE MODULE FOR THE REMOTE STARTER PROGRAMMING.

Module label

Notice: Updated Firmware and Installation Guides Updated fi rmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest firmware and download the latest installation guide(s) prior to the installation of this product

WARNING
The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualified technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.

TECH SUPPORT
Tél: 514-255-HELP (4357)
1-877-336-7797
ADDENDUM GUIDE

WEB UPDATE | MISE À JOUR INTERNET
www.fortinbypass.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>