V I V O STAND-V001UVM Single Monitor Desk Mount Instruction Manual
- June 12, 2024
- V I V O
Table of Contents
Single Monitor Desk Mount
Instruction Manual
SKU: STAND-V001UVM
STAND-V001UVM Single Monitor Desk Mount
Scan the QR code with your mobile device or follow the link for helpful videos
and specifications related to this product.
https://vivo-us.com/products/stand-v001uvm
https://vivo-us.com/products/stand-
v001uvm
GET IN TOUCH
Monday-Friday from 7:00am-7:00pm CST
help@vivo-us.com
www.vivo-us.com
309-278-5303
Chat live with an agent!
WARNING!
If you do not understand these directions, or if you have any doubts about the
safety of the installation, please call a qualified technician. Check
carefully to make sure there are no missing or defective parts. Improper
installation may cause damage or serious injury. Do not use this product for
any purpose that is not explicitly specified in this manual. Do not exceed
weight capacity. We cannot be liable for damage or injury caused by improper
mounting, incorrect assembly or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT
TIPOVER:
- NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
- USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
TOOLS NEEDED
Phillips Screwdriver
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
ASSEMBLY STEPS
STEP 1 – Option A – Desk Clamp
Loosen the hand screw on Clamp (B) to open fully, as shown below.
Install the Clamp (B) to the Pole (A) using M6x16mm Screws (S-A) and tighten using 3mm Allen Wrench (T-A). Mount assembly to the desktop and tighten using the hand screw.
STEP 1 – Option B – Grommet
Disassemble Clamp (B) into individual parts. Remove Clamp Plate (B1) using
Phillips screwdriver and remove Knob (B2).
Install Grommet Plate (F) to the Pole (A) using M6x16mm Screws (S-A) and 3mm
Allen Wrench (T-A).
Attach Soft Pad (G) to the Grommet Plate (F). Position Pole (A) on the
mounting surface and secure using Clamp Plate (B1) and Knob (B2).
If desk does not have an existing grommet hole, drill a 3/8” (10mm) diameter hole at the desired position through the mounting surface.
STEP 2
Slide Pole Cable Clip (J) and Swivel Arm (C) onto Pole (A). Tighten Swivel Arm
(C) at desired height using 5mm Allen Wrench (T-B). Insert Pole Cap (E) into
top of Pole (A).
STEP 3
Attach Cable Clips (I) onto each segment of Swivel Arm (C).
STEP 4
With the adjustment screw holes on top, mount Adapter (H) to to VESA Plate (D)
using M4x16mm Thumbscrews (S-C) with M4 Washers (S-D) and a Phillips
screwdriver. Loosly install remaining M4x16mm Thumbscrews (S-C) into the top
adjustment holes in Adapter (H).
To adjust the Adapter (H) to fit the device, push device down onto springloaded tabs and position device against the face of the adapter. With previously installed M4x16mm Thumbscrews (S-C) still loose, center the device on the adapter, then tighten the Thumberscrews.
To remove the device for any reason, hold both sides of the device, pull down, tilt the devide, then lift it out. Reinstall the device in reverse order.
STEP 5
NOTE: Before proceeding, ensure that the tilt joint on Swivel Arm (C) is
tight. Use 5mm Allen Wrench (T-B) to secure tilt joint.
STEP 6
Slide VESA Plate (D) with adapter and tablet onto the head of Swivel Arm (C).
Install the M6 Security Nut (S-B).
STEP 7
Manage cables in Cable Clips (I) and Pole Cable Clip (J).
ADJUST AS DESIRED
Tighten the screw with the supplied 5mm Allen Wrench (T-B) to fix the tilt
angle and to make any necessary adjustments.
OPTIONAL USE: MONITOR MOUNT
To use stand as single monitor mount, follow Steps 1-3, then return to these
instructions to proceed.
STEP 4B
Flat Back Monitor
Attach the VESA Plate (D) to the monitor with Thumbscrews (M-A) and a Phillips
screwdriver.
NOTE: Hand tighten screws to avoid over tightening.
Curved Back Monitor
Attach the VESA Plate (D) to the monitor with M4x30mm Screws (M-B), M6 Spacers
(M-C) and a Phillips screwdriver. NOTE: Gently tighten using a screwdriver.
STEP 5B
Slide VESA Plate (D) with monitor onto the head of Swivel Arm (C). Install the
M6 Security Nut (S-B).
Make sure the security nut is installed before you rotate the monitor.
STEP 6B
Manage cables in Cable Clips (I) and Pole Cable Clip (J).
Adjust as Desired
Tighten the screw with the supplied 5mm Allen Wrench (T-B) to fix the tilt
angle and to make any necessary adjustments.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
LAST UPDATED: 07/13/2023
REV1.1
Open Monday – Friday 7:00am – 7:00pm CST,
our dedicated support team can offer immediate assistance with rapid response
times. If any parts are received damaged or defective, please contact us. We
are happy to replace parts to ensure you have a fully functioning product.
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within office hrs): < 15 M
309-278-5303
AVG. RESOLUTION TIME (within office hrs): 5M 4S
help@vivo-us.com
AVG. RESPONSE TIME (within office hrs): 1HR 8M
– 23% within < 15m
– 38% within < 30m
– 61% within < 1hr
– 83% within < 2hr
– 92% within < 3hr
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-
us.com
Documents / Resources
| V I
V O STAND-V001UVM Single Monitor Desk
Mount
[pdf] Instruction Manual
STAND-V001UVM, STAND-V001UVM Single Monitor Desk Mount, Single Monitor Desk
Mount, Monitor Desk Mount, Desk Mount, Mount
---|---
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Tablet Holder and Desk Mount – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>