LeoVince 14363E LV One EVO Slip On Exhaust Instruction Manual
- June 13, 2024
- LeoVince
Table of Contents
TECHNICAL INFORMATION ART.
14363E
SLIP-ON
LV ONE EVO
KTM 690 ENDURO R
KTM 690 SMC R
(Also fits 35kW version)
TYPE: KTM 690 LC4; A/-, B /-
14363E LV One EVO Slip On Exhaust
STAINLESS S.
1 – Muffler| cod. 3014363482
2 – Link pipe| cod. 3014363201
3 – Fitting kit| cod. 3014363601
PESO – WEIGHT – POIDS – GEWICHT (Kg)
ORIGINALE – STOCK – ORIGINE – ORIGINAL 4,467 (Kg)
| Stainless steel| Carbon| Titanium
LeoVince| 3,81| /| /
ART. 14363E
KTM 690 ENDURO R / 690 SMC R (Also fits 35kW version)
SLIP-ON – LV ONE EVO – STAINLESS STEEL
ART. 14363E – SPARE PARTS
KTM 690 ENDURO R / 690 SMC R (Also fits 35kW version)
A FITTING KIT cod.3014363601R
FITTING INSTRUCTION
LIST OF SUPPLIED PARTS:
Refer to the list of components and the product drawing included in this
booklet.
WARNING:
before carrying out any work on the exhaust, check that its surface has cooled
so that it will not damage components, which are not heat-resistant (such as
fairing, hoses, rubber sleeves, etc.), or the operator.
INSTALLATION:
-
Remove the OE silencer. (Photos 1-2-3-4)
-
Slide the Leovince silencer onto the link pipe, check the alignment of the mounting eyes for the springs and the alignment of the exhaust outlet to the rear of the silencer, and then link the parts together with the springs provided (Photo 6)
-
Check that the mating surfaces are in good clean condition, slide the link pipe on to the original header, taking care not to damage the graphite bushing (if supplied) which should replace the OE bushing. Partially tighten the securing strap to allow a degree
of further adjustment. -
Mount spacers, washers and brackets (if any) as shown on the drawing and then secure by tightening nuts and bolts
-
Tighten the various clamps which join the Leovince link pipe to the OE exhaust headers.
-
Start the engine, wait a few minutes until it reaches operating temperature, and check that there are no gas leaks.
IMPORTANT:
During the first km of running, the exhaust system needs breaking-in;
therefore, slight gas leakage might occur. After approximately 100 Km, check
all the fasteners.
ADJUSTEMENT:
This silencer has been developed by Leovince on an electronic dynamometer
using a vehicle in perfect condition, and in standard trim
MAINTENANCE:
From time to time, check all the brackets and fasteners, which could be
affected by use (sound-deadening material, seals and other rubber parts) and
replace them periodically.
The silencer may be cleaned using gasoline, diesel oil or alcohol. Absolutely
avoid the use of any kind of solvent.It is normal for there to be some
discolouration of the silencer, which is the result of heat and the nature of
the materials used.
IT IS FORBIDDEN to modify silencers. Whatever form this may take,
Belgrove Sp. z o.o. declines any responsibility for defects, problems, or
malfunction, arising from the use of any product which has been modified or
tampered with.
We suggest the fitting to be made by professionals
ART. 14363E
Nome………………………..
Cognome……………………..
Indirizzo …………………
Targa veicolo…………………
Tel…………………………..
Date and seller’s stamp
NOTE………………………………………….
leovince.com –
[email protected]
Europe Customer Service: [email protected]
USA Customer Service: [email protected]
+1-844-536-7625