LeoVince 14399 Gp Style Stainless Steel Slip-On Instructions
- October 27, 2023
- LeoVince
Table of Contents
TECHNICAL INFORMATION
ART. 14399 SLIP-ON GP-STYLE
SCRAMBLER 800 ICON / DARK
(also fits 35 kW version)
TYPE: 3K; 00/AA – 4K; 35/AA
14399 Gp Style Stainless Steel Slip-On
ART. 14399
Nome……………………………………………………………………………
Surname……………………………………………………………………….
Address………………………………………………………………………..
Vehicle registration plate………………………………………………
Tel………………………………………………………………………………..
Date and seller’s stamp…………………………………………………
LIST OF COMPONENTS
1 – Muffler
2 – Link pipe
3 – Fitting kit| STAINLESS STEEL
cod. 308124471
cod. 3014399201
cod. 3014399601
---|---
WEIGHT
STOCK 6,68 (Kg)
| Stainless steel| S.s full black| Titanium
LeoVince| /| 1,92| /
DUCATI SCRAMBLER 800 ICON / DARK (also fits 35kW version)
SLIP-ON – GP STYLE – STAINLESS STEEL
ART. 14399 – SPARE PARTS
DUCATI SCRAMBLER 800 ICON / DARK (also fits 35kW version)
A FITTING KIT cod.3014399601R
FITTING INSTRUCTION
LIST OF SUPPLIED PARTS:
Refer to the list of components and the product drawing included in this booklet.
WARNING: before carrying out any work on the exhaust, check that its surface has cooled so that it will not damage components, which are not heat- resistant (such as fairing, hoses, rubber sleeves, etc.), or the operator.
INSTALLATION:
- Remove the original silencer. (Photo 1-2-3-4-5)
- Check that the mating surfaces are in good clean condition, slide the link pipe on to the original header, taking care not to damage the graphite bushing (if supplied) which should replace the OE bushing. Partially tighten the securing strap to allow a degree of further adjustment.
- Attach the support bracket to the motorcycle frame using the supplied screw. (Photo 5)
- Slide the Leovince silencer onto the link pipe, check the alignment of the mounting eyes for the springs and the alignment of the exhaust outlet to the rear of the silencer, and then link the parts together with the springs provided
- Mount spacers, washers and brackets (if any) as shown on the drawing and then secure by tightening nuts and bolts. (Photo 6)
- Tighten the various clamps which join the Leovince link pipe to the OE exhaust headers.
- Start the engine, wait a few minutes until it reaches operating temperature, and check that there are no gas leaks.
IMPORTANT:
During the first km of running, the exhaust system needs breaking-in;
therefore, slight gas leakage might occur. After approximately 100 Km, check
all the fasteners.
ADJUSTEMENT:
This silencer has been developed by Leovince on an electronic dynamometer
using a vehicle in perfect condition, and in standard trim
MAINTENANCE:
From time to time, check all the brackets and fasteners, which could be affected by use (sound-deadening material, seals and other rubber parts) and replace them periodically. The silencer may be cleaned using gasoline, diesel oil or alcohol. Absolutely avoid the use of any kind of solvent.It is normal for there to be some discolouration of the silencer, which is the result of heat and the nature of the materials used.
IT IS FORBIDDEN to modify silencers. Whatever form this may take, Belgrove Sp. z o.o. declines any responsibility for defects, problems, or malfunction, arising from the use of any product which has been modified or tampered with.
We suggest the fitting to be made by professionals
PHOTO 1
PHOTO 2
PHOTO 3
PHOTO 4
PHOTO 5
PHOTO 6
12-04-22 REV.01
USA Customer Service:
[email protected] – +1-844-536-7625
leovince.com –
[email protected]
Europe Customer Service:
[email protected]