LeoVince SLIP-ON GP Corsa EVO Slip On Exhaust Owner’s Manual

June 10, 2024
LeoVince

LeoVince SLIP-ON GP Corsa EVO Slip On Exhaust

Product Information

The product is a slip-on LV-10 carbon exhaust system designed for the Ducati Scrambler 800 Icon/Dark (including the 35 kW version). It comes with a muffler, link pipe, and fitting kit. The product code for the carbon muffler is 3015200481, the link pipe is 3015250201, and the fitting kit is 3015250601. The exhaust system is made of 3K/4K carbon fiber and weighs 6.68 kg. The product also includes spare parts such as a stainless steel bracket, knurled collar nuts, Allen screws, short helical spring tensile, and a muffler repack kit.

Product Usage Instructions

  1. Refer to the list of components and product drawings provided in the manual.
  2. Ensure that the surface temperature of the engine block and exhaust system is safe to work with.
  3. Remove the original muffler.
  4. Check the coupling surfaces and put on the link pipe on the original tubing, taking care not to damage the graphite gasket.
  5. Partially tighten the sealing clamp to allow for minor adjustments.

CARBON FIBER

  1. Muffler: cod. 3015200481
  2. Link pipe: cod. 3015250201
  3. Fitting kit: cod. 3015250601

PESO – WEIGHT – POIDS – GEWICHT   (Kg)

ORIGINALE – STOCK – ORIGINE – ORIGINAL                             6,68 (Kg)

 | Stainless steel| Carbon| Titanium

LeoVince

|

/

|

1,13

|

/

ART. 15250C

LeoVince-SLIP-ON-GP-Corsa-EVO-Slip-On-Exhaust-fig-3

  • DUCATI SCRAMBLER 800 ICON / DARK (also fits 35kW version) SLIP-ON – LV-10 – CARBON

ART. 15250C – SPARE PARTS

LeoVince-SLIP-ON-GP-Corsa-EVO-Slip-On-Exhaust-fig-8

  • DUCATI SCRAMBLER 800 ICON / DARK (also fits 35kW version) A FITTING KIT cod.3015250601R

FITTING INSTRUCTION

LIST OF SUPPLIED PARTS
Refer to the list of components and the product drawing included in this booklet.

WARNING
before carrying out any work on the exhaust, check that its surface has cooled so that it will not damage components, which are not heat-resistant (such as fairing, hoses, rubber sleeves, etc.), or the operator.

INSTALLATION

  1. Remove the original silencer. (Photo 1-2-3-4-5).LeoVince-SLIP-ON-GP-Corsa-EVO-Slip-On-Exhaust-fig-6 LeoVince-SLIP-ON-GP-Corsa-EVO-Slip-On-Exhaust-fig-7LeoVince-SLIP-ON-GP-Corsa-EVO-Slip-On-Exhaust-fig-4 LeoVince-SLIP-ON-GP-Corsa-EVO-Slip-On-Exhaust-fig-1
  2. Check that the mating surfaces are in good clean condition, and slide the link pipe on to the original header, taking care not to damage the graphite bushing (if supplied) which should replace the OE bushing. Partially tighten the securing strap to allow a degree of further adjustment.
  3. Attach the support bracket to the motorcycle frame using the supplied screw. (Photo 5).
  4. Slide the Leovince silencer onto the link pipe, check the alignment of the mounting eyes for the springs and the alignment of the exhaust outlet to the rear of the silencer, and then link the parts together with the springs provided.
  5. Mount spacers, washers, and brackets (if any) as shown on the drawing and then secure by tightening nuts and bolts. (Photo 6).LeoVince-SLIP-ON-GP-Corsa-EVO-Slip-On-Exhaust-fig-2
  6. Tighten the various clamps which join the Leovince link pipe to the OE exhaust headers.
  7. Start the engine, wait a few minutes until it reaches operating temperature, and check that there are no gas leaks.

IMPORTANT
During the first km of running, the exhaust system needs to break in; therefore, slight gas leakage might occur. After approximately 100 Km, check all the fasteners.

ADJUSTMENT
This silencer has been developed by Leovince on an electronic dynamometer using a vehicle in perfect condition, and in standard trim.

MAINTENANCE

From time to time, check all the brackets and fasteners, which could be affected by use (sound-deadening material, seals, and other rubber parts), and replace them periodically. The silencer may be cleaned using gasoline, diesel oil, or alcohol. Absolutely avoid the use of any kind of solvent. It is normal for there to be some discoloration of the silencer, which is the result of heat and the nature of the materials used.

IT IS FORBIDDEN to modify silencers. Whatever form this may take, Belgrove Sp. z o.o. declines any responsibility for defects, problems, or malfunction, arising from the use of any product which has been modified or tampered with.

We suggest the fitting be made by professionals

at leovince.cominfo@leovince.com. Europe Customer Service: info@leovince.com. USA Customer Service: infousa@leovince.com. – +1-844-536-7625

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals