LeoVince 15200C Exhaust Muffler Instruction Manual

June 10, 2024
LeoVince

15200C Exhaust Muffler

TECHNICAL INFORMATION
ART. 15200C
SLIP-ON
LV-10 CARBON
KAWASAKI ZX-10 R / RR NINJA
(Low & High mount)
TYPE: ZXT00S- ZXT02C – ZXT02E – ZXT02L

ART. 15200C……………
Given name…………
Surname………..
Address……………
Vehicle registration plate…………
Tel………………
Date and seller’s stamp………

LIST OF COMPONENTS

1 – Muffler
2 – Link pipe 1154
3 – Link pipe 1155
4 – Fitting kit
CARBON FIBER
cod. 3015200481
cod. 3015200211
cod. 3015200213
cod. 3015200601

STANDARD LINK PIPELeoVince 15200C Exhaust Muffler - diagram
1 HIGH MOUNT LINK PIPE

LeoVince 15200C Exhaust Muffler - diagram 2

ART. 15200C
KAWASAKI ZX-10 R NINJA / RR NINJA
SLIP-ON – LV-10 – CARBON
STANDARD LINK PIPE

HIGH MOUNT LINK PIPELeoVince 15200C Exhaust Muffler - diagram
4

ART. 15200C SPARE PARTS
KAWASAKI ZX-10 R NINJA / RR NINJA
A FITTING KIT cod. 3015200601R
FITTING INSTRUCTION

LIST OF SUPPLIED PARTS:

Refer to the list of components and the product drawing included in this booklet.
WARNING:
before carrying out any work on the exhaust, check that its surface has cooled so that it will not damage components, which are not heat-resistant (such as fairing, hoses, rubber sleeves, etc.), or the operator.

INSTALLATION:

  1. Remove the OE silencer.
  2. Check that the mating surfaces are in good clean condition, slide the link pipe on to the original header, taking care not to damage the graphite bushing (if supplied) which should replace the OE bushing. Partially tighten the securing strap to allow a degree of further adjustment.
  3. Slide the Leovince silencer onto the link pipe, check the alignment of the mounting eyes for the springs and the alignment of the exhaust outlet to the rear of the silencer and then link the parts together with the spring provided
  4. Mount spacers, washers and brackets (if any) as shown on the drawing and then secure by tightening nuts and bolts.
  5. Tighten the various clamps which join the Leovince link pipe to the OE exhaust headers.
  6. Start the engine, wait a few minutes until it reaches operating temperature, and check that there are no gas leaks.

IMPORTANT:
During the first km of running, the exhaust system needs breaking-in; therefore, slight gas leakage might occur. After approximately 100 Km, check all the fasteners.
ADJUSTEMENT:
This silencer has been developed by Leovince on an electronic dynamometer using a vehicle in perfect condition, and in standard trim

MAINTENANCE:

From time to time, check all the brackets and fasteners, which could be affected by use (sound-deadening material, seals and other rubber parts) and replace them periodically. The silencer may be cleaned using gasoline, diesel oil or alcohol. Absolutely avoid the use of any kind of solvent.It is normal for there to be some discolouration of the silencer, which is the result of heat and the nature of the materials used.
IT IS FORBIDDEN to modify silencers. Whatever form this may take, Belgrove Sp. z o.o. declines any responsibility for defects, problems, or malfunction,  arising from the use of any product which has been modified or tampered with.
We suggest the fitting to be made by professionals

 Ieovince.cominfo@leovince.com
Europe Customer Service: info@leovince.com
USA Customer Service: infousa@leovince.com – +1-844-536-7625
LeoVince 15200C Exhaust Muffler - logo 1

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals