ZEVNI Z-F8F3IFIR-59W3 3-Light Polished Brass Wall Sconce Instruction Manual

ZEVNI Z-F8F3IFIR-59W3 3-Light Polished Brass Wall Sconce

Product Information

The product is a lamp that requires installation by a licensed electrician to reduce the risk of fire, electric shock, or personal injury. The manual contains safety instructions that must be followed before starting assembly and installation. The lamp can only be installed on a ceiling or wall that can withstand its weight and uses a voltage of 120V. The maximum wattage is Type A, Max 60W per bulb. The lamp should be kept away from acidic and alkaline substances to avoid damaging its surface. The product comes with mounting plate (C), green ground screw (D), back plate (E), stud (F), socket (G), lampshade (H), socket ring (I), mounting screw (A), and plastic wire connector (B). Tools required for assembly and installation include a ladder, Philips Head or Flat Blade Screwdriver, Electrical Tape, Pliers, and Wire Cutter/Stripper.

Product Usage Instructions

1. Before starting assembly and installation, make sure to turn off the electricity and NEVER attempt any work without shutting off the power until the work is done.
2. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the illustration.
3. Secure mounting plate (C) to the outlet box with mounting screws (A).
4. Connect wires according to the chart provided in the manual. Make sure to connect the ground wire to the green ground screw (D) and never connect other wires to ground wires.
5. Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
6. Attach the back plate (E) to the mounting plate (C) using the removed studs (F).
7. Attach the socket (G) to the back plate (E) and then attach the lampshade (H) to the socket ring (I).
8. When replacing bulbs, turn off or unplug the lamp and wait until it is cool as bulbs get hot quickly.

Item Number: Z-F8F3IFIR-59W3
WARNING (To reduce the risk of fire, electric shock, or personal injury):

1. We suggest installation by a licensed electrician.

2. Please read the instruction carefully and save it as you may need it at a later time.

3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.

   • » Go to the main fuse, or circuit breaker, box in your home.
     Place the main power switch in the “OFF” position.

   • » Place the wall switch in the “OFF” position.

4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.

5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.

6. Make sure the voltage you are using is 120V. The maximum wattage is Type A, Max 60W per bulb.

7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.

8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.

9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

**TOOLS REQUIRED

**

(NOT INCLUDED):
Before starting assembly and installation please prepare the needed tools as below picture

PARTS INCLUDING

• (C) Mounting plate (1)
• (D) Green ground screw (1)
• (E) Back plate (1)
• (F) Stud (2)
• (G) Socket (3)
• (H) Lampshade (3)
• (I) Socket ring (3)

ACCESSORIES ENCLOSED:

• (A) Mounting screw (2)
• (B) Plastic wire connector (3)

ASSEMBLY & INSTALLATION INSTRUCTIONS

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.

2. Turn off power
   Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.

   • » Go to the main fuse, or circuit breaker, box in your home.
     Place the main power switch in the “OFF” position.

   • » Place the wall switch in the “OFF” position.

3. Make assembly

• Step A1 » Unscrew studs (F) from back plate (E), then set them aside for later installation.
• Step A2 Carefully pass the supply wires from the outlet box through mounting plate (C).Secure mounting plate (C) to the outlet box with mounting screws (A).
• Step A3 »  Make wire connections

Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.

Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then  tuck all wires into the outlet box.

• Step A4 » Align the holes in back plate (E) and mounting plate (C), then secure them with the previously removed studs (F).
• Step A5 »
  1. Remove socket rings (I) from sockets (G).
  2. Carefully place lampshades (H) on sockets (G).
  3. Secure lampshades (I) to sockets (G) with socket rings (I).
  4. Install bulbs (Not included) (Please do not exceed the maximum wattage recommended on the socket.)

Check everything is installed properly, then you could turn on the light. Enjoy!

ORDERING PARTS.
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.

CLEANING

To clean, wipe the fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>