LeoVince 15302 Slip On Exhaust Instruction Manual

June 10, 2024
LeoVince

LeoVince 15302 Slip On Exhaust

LeoVince-15302-Slip-On-Exhaust-PRODUCT

Product Information

The product is a slip-on exhaust system for Honda CRF 1100 L Africa Twin, Adventure Sport, and DCT motorcycles. It comes in three variants – LV-12, LV-12 Black, and LV-12 Titanium. The product is compatible with the original panniers and fits with SD08 and SD09 types of 1/1, 2/1, 3/1, and 4/1.

The package contains:

  • Muffler
  • Link pipe
  • Fitting kit
  • Heat shield
  • Valve block-off kit

The product is made of stainless steel, black-coated stainless steel, or titanium.

Product Usage Instructions

  1. Install the Leovince valve canceller bracket (206609) with the writing “up” facing outwards and secure it to the servo motor shaft with the original M3 screw.
  2. Remove the original plastic pulley by loosening the retaining screw.
  3. Mount the Leovince valve block-off kit (206609) provided in the package with the writing “up” facing outwards and secure it to the motor shaft with the original M3 screw.
  4. Reassemble the servo motor and other components in the original position by proceeding in reverse order.

Note: Refer to the fitting instructions for detailed information on mounting the product components.

  • Given name
  • Surname
  • Address
  • Vehicle registration plate
  • Tel.
  • Date and seller’s stamp

Install the leovince valve canceller bracket(206609)supplied in the box with the writing”up”facing outwards (as in the picture) and secure it to the servo motor shaft with the original m3 screw. reassemble the servo motor and the other components in the original position proceeding in reverse order.

Loosen the retaining screw and remove the original plastic pulley.

LIST OF COMPONENTS

STAINLESS S. BLACK TITANIUM

  1. Muffler  cod. 3015302481 cod. 3015300485 cod. 3015300486
  2. Link pipe cod. 3015302201 cod. 3015302201 cod. 3015302201
  3. Fitting kit cod. 3015302601 cod. 3015302601 cod. 3015302601
  4. Heat shield cod. 3015302001 cod. 3015302001 cod. 3015302001
  5. Valve block-off cod. 206609 cod. 206609 cod. 206609

Pull the servo motor partially out as shown in the picture, loosen the three visibile screws and remove the plastic housing to access the actuator cables. Disconnect the two actuator cables and remove the servo motor.

Unplug the connector.

Remove the brake fluid  reservoir.

Remove the two screws and the clip shown in the pictures.

PESO – WEIGHT – POIDS – GEWICHT   (Kg)

ORIGINALE – STOCK – ORIGINE – ORIGINAL                             5,96 (Kg)

| Stainless steel| S.s. Black| Titanium

LeoVince

|

5,67

|

5,67

|

5,08

KIT VALVOLA

ART.15302-15302B-15302T-14355E-14355EB

HONDA CRF 1100 L AFRICA TWIN/ADVENTURE SPORT/DCT

INSTRUCTIONS FOR ASSEMBLY OF PARTS AVOIDING THE RAISING OF AN ALARM SIGNALLING FOR NO EXHAUST VALVE
BY REMOVING THE STOCK EXHAUST, ALSO THE EXHAUST VALVE IS REMOVED CAUSING THE LIGHTING OF THE ALARM ON THE DASHBOARD. TO AVOID THE LIGHTING OF THE ALARM, IT IS NECESSARY TO INSTALL THE ALARM BLOCK KIT SUPPLIED IN THE PACKAGING OPERATING AS FOLLOW:LeoVince-15302-Slip-On-Exhaust-FIG
8

ART. 15302
HONDA CRF 1100 L AFRICA TWIN/ADVENTURE SPORT/DCT (fits with original panniers)

  • A FITTING KIT cod. 3015302601R
  • B CARBON COVER KIT cod. 3015302001RLeoVince-15302-Slip-On-Exhaust-FIG 13

ART. 15302B
HONDA CRF 1100 L AFRICA TWIN/ADVENTURE SPORT/DCT
(fits with original panniers)
SLIP-ON – LV-12 – BLACK – APPROVEDLeoVince-15302-Slip-On-Exhaust-FIG
14

ART. 15302B
HONDA CRF 1100 L AFRICA TWIN/ADVENTURE SPORT/DCT
(fits with original panniers)

  • A FITTING KIT cod. 3015302601R
  • B CARBON COVER KIT cod. 3015302001R

LeoVince-15302-Slip-On-Exhaust-FIG 15

ART. 15302T
HONDA CRF 1100 L AFRICA TWIN/ADVENTURE SPORT/DCT
(fits with original panniers)
SLIP-ON – LV-12 – TITANIUM – APPROVEDLeoVince-15302-Slip-On-Exhaust-FIG
16

ART. 15302T
HONDA CRF 1100 L AFRICA TWIN/ADVENTURE SPORT/DCT
(fits with original panniers)

  • A FITTING KIT cod. 3015302601R
  • B CARBON COVER KIT cod. 3015302001R

LIST OF SUPPLIED PARTS:
Refer to the list of components and the product drawing included in this booklet.

WARNING:
before carrying out any work on the exhaust, check that its surface has cooled so that it will not damage components, which are not heat-resistant (such as fairing, hoses, rubber sleeves, etc.), or the operator.

INSTALLATION

  1. Remove the original heat shield.
    Disconnect the exhaust valve according to the instructions provided.
    “KIT VALVOLA ART.15302-15302B-15302T-14355E-14355EB”

  2. Remove the OE silencer.

  3. Check that the mating surfaces are in good clean condition, slide the link pipe on to the original header, taking care not to damage the graphite bushing (if supplied) which should replace the OE bushing. Partially tighten the securing strap to allow a degree of further adjustment.

  4. Slide the Leovince silencer onto the link pipe, check the alignment of the mounting eyes for the springs and the alignment of the exhaust outlet to the rear of the silencer, and then link the parts together with the springs provided

  5. Fit the clamps to the silencer. Mount spacers, washers and brackets (if any) as shown on the drawing and then secure by tightening nuts and bolts.

  6. Tighten the various clamps which join the Leovince link pipe to the OE exhaust headers.

  7. Start the engine, wait a few minutes until it reaches operating temperature, and check that there are no gas leaks.

IMPORTANT:
During the first km of running, the exhaust system needs breaking-in; therefore, slight gas leakage might occur. After approximately 100 Km, check all the fasteners.

ADJUSTMENT

This silencer has been developed by Leovince on an electronic dynamometer using a vehicle in perfect condition, and in standard trim

MAINTENANCE

From time to time, check all the brackets and fasteners, which could be affected by use (sound-deadening material, seals and other rubber parts) and replace them periodically.
The silencer may be cleaned using gasoline, diesel oil or alcohol. Absolutely avoid the use of any kind of solvent.It is normal for there to be some discolouration of the silencer, which is the result of heat and the nature of the materials used.
IT IS FORBIDDEN to modify silencers. Whatever form this may take, Belgrove Sp. z o.o. declines any responsibility for defects, problems, or malfunction, arising from the use of any product which has been modified or tampered with.
We suggest the fitting to be made by professionals

USA Customer Service:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals