LeoVince 15242T Slip-On Exhaust Instruction Manual
- June 10, 2024
- LeoVince
Table of Contents
LeoVince 15242T Slip-On Exhaust
Product Information
The product is a slip-on exhaust system with the code ART. 15242T LV-10 Titanium, designed for Husqvarna Svartpilen/Vitpilen 125/401 motorcycles with the following types: HQV 125; A/-, B/- HQV 401; A1/-, B1/-. The exhaust system comes with a muffler, a link pipe, and a fitting kit made of titanium.
Product Usage Instructions
- Check the list of components supplied with the product against the product drawing in the manual.
- Before starting any operation, make sure the surface temperature of the engine block and exhaust system is not hot enough to cause damage to the operator or non-heat-resistant parts (fairings, pipes, sheaths, etc.).
- Remove the original muffler.
- After verifying the good condition of the coupling surfaces, fit the manifold onto the original pipe, taking care not to damage graphite gasket, which should be replaced with the supplied one if provided. Partially tighten the seal clamp to allow for minimal adjustments.
- Fit the muffler onto the link pipe and connect it to the manifold. Tighten all bolts and screws according to the torque specifications in the manual.
- Start the engine and wait a few minutes until it reaches operating temperature. Check for gas leaks. It is recommended to have the installation carried out by a specialist.
LIST OF COMPONENTS
- Muffler
- Link pipe
- Fitting kit
ART.15242T
HUSQVARNA SVARTPILEN / VITPILEN 125 / 401
SLIP-ON – LV-10 – TITANIUM
ART.15242T – SPARE PARTS
HUSQVARNA SVARTPILEN / VITPILEN 125 / 401
- A FITTING KIT cod.3015242601R
FITTING INSTRUCTION
LIST OF SUPPLIED PARTS:
Refer to the list of components and the product drawing included in this
booklet.
WARNING :
before carrying out any work on the exhaust, check that its surface has cooled
so that it will not damage components, which are not heat-resistant (such as
fairing, hoses, rubber sleeves, etc.), or the operator.
INSTALLATION:
- Remove the OE silencer.
- Check that the mating surfaces are in good clean condition, slide the link pipe on to the original header, taking care not to damage the graphite bushing (if supplied) which should replace the OE bushing. Partially tighten the securing strap to allow a degree of further adjustment.
- Slide the Leovince silencer onto the link pipe, check the alignment of the mounting eyes for the springs and the alignment of the exhaust outlet to the rear of the silencer, and then link the parts together with the springs provided
- Mount spacers, washers and brackets (if any) as shown on the drawing and then secure by tightening nuts and bolts.
- Tighten the various clamps which join the Leovince link pipe to the OE exhaust hea-ders.
- Start the engine, wait a few minutes until it reaches operating temperature, and check that there are no gas leaks.
IMPORTANT:
During the first km of running, the exhaust system needs breaking-in;
therefore, slight gas leakage might occur. After approximately 100 Km, check
all the fasteners.
ADJUSTEMENT:
This silencer has been developed by Leovince on an electronic dynamometer
using a vehicle in perfect condition, and in standard trim
MAINTENANCE:
From time to time, check all the brackets and fasteners, which could be
affected by use (sound-deadening material, seals and other rubber parts) and
replace them periodically. The silencer may be cleaned using gasoline, diesel
oil or alcohol. Absolutely avoid the use of any kind of solvent.It is normal
for there to be some discolouration of the silencer, which is the result of
heat and the nature of the materials used.
IT IS FORBIDDEN to modify silencers. Whatever form this may take, Belgrove Sp.
z o.o. declines any responsibility for defects, problems, or malfunction,
arising from the use of any product which has been modified or tampered with.
We suggest the fitting to be made by professionals
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>