LeoVince 14171E, 14172E KAWASAKI Z900, Z900 A2 Exhaust Instruction Manual
- June 10, 2024
- LeoVince
Table of Contents
LeoVince 14171E, 14172E KAWASAKI Z900, Z900 A2 Exhaust
Product Information Art. 14171E-14172E Slip-On LV Pro/LV Pro Carbon
Kawasaki Z900/Z900 A2
This product is a slip-on exhaust system designed to fit Kawasaki Z900 and Z900 A2 motorcycles, including 35kW and 70kW versions. It is available in two types: LV Pro and LV Pro Carbon. The product is supplied with a muffler, link pipe, clamp, bracket, and fitting kit. The product is made of either stainless steel or carbon fiber, depending on the variant selected. The weight of the product varies depending on the material used. The product has an E13 92R-01 10393 certification.
Product Usage Instructions
- Check that all the components listed in the manual are present in the package.
- Remove the original silencer from the motorcycle.
- If you are using the Art. 14171E link pipe, remove the original graphite bushing before assembling it with the LeoVince link pipe
- Install the LeoVince muffler onto the link pipe.
- Install the clamp and bracket onto the muffler.
- Mount the entire assembly onto the motorcycle.
- Start the engine and wait for it to reach operating temperature. Check for gas leaks.
- We recommend that you seek the assistance of a specialist for installation.
Please refer to the manual for more detailed instructions and illustrations of the installation process.
LIST OF COMPONENTS
- Muffler
- Link pipe
- Clamp
- Bracket
- Fitting kit
LIST OF SUPPLIED PARTS
Refer to the list of components and the product drawing included in this booklet.
WARNING:
before carrying out any work on the exhaust, check that its surface has cooled
so that it will not damage components, which are not heat-resistant (such as
fairing, hoses, rubber sleeves, etc.), or the operator.
INSTALLATION
- Remove the OE silencer.
- Check that the mating surfaces are in good clean condition, slide the link pipe on to the original header, taking care not to damage the graphite bushing (if supplied) which should replace the OE bushing. Partially tighten the securing strap to allow a degree of further adjustment.
- Slide the Leovince silencer onto the link pipe, check the alignment of the mounting eyes for the springs and the alignment of the exhaust outlet to the rear of the silencer, and then link the parts together with the springs provided
- Fit the clamps to the silencer. Mount spacers, washers and brackets (if any) as shown on the drawing and then secure by tightening nuts and bolts.
- Tighten the various clamps which join the Leovince link pipe to the OE exhaust headers.
- Start the engine, wait a few minutes until it reaches operating temperature, and check that there are no gas leaks.
IMPORTANT:
During the first km of running, the exhaust system needs breaking-in;
therefore, slight gas leakage might occur. After approximately 100 Km, check
all the fasteners. It is normal for some white smoke to appear the first time
you use the exhaust, even after switching off the engine.
ADJUSTMENT
This silencer has been developed by Leovince on an electronic dynamometer using a vehicle in perfect condition, and in standard trim
MAINTENANCE
From time to time, check all the brackets and fasteners, which could be affected by use (sound-deadening material, seals and other rubber parts) and replace them periodically. The silencer may be cleaned using gasoline, diesel oil or alcohol. Absolutely avoid the use of any kind of solvent.It is normal for there to be some discolouration of the silencer, which is the result of heat and the nature of the materials used. IT IS FORBIDDEN to modify silencers. Whatever form this may take, Belgrove Sp. z o.o. declines any responsibility for defects, problems, or malfunction, arising from the use of any product which has been modified or tampered with. We suggest the fitting to be made by professionals
International Customer Service:
info@leovince.com
North America Customer Service:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>