ROADSAFE R-Launch Electronic Throttle Controller Instruction Manual

ROADSAFE R-Launch Electronic Throttle Controller

Product Information

product
and the vehicle.
Light sensor| A sensor that detects the ambient light levels for proper
functioning of the product.
Accelerator connector attachment pedal| An attachment pedal that connects to the accelerator and
enables the product to function.
Sensitivity adjustment (up/down)| A control feature that allows adjusting the sensitivity of the
product up or down.

Product Usage Instructions

Before installing the product, please follow these steps:

1. Visit our website at roadsafe.com.au to access the latest fitting instructions.
2. Compare the number in the top left corner (V) of the product with the number on our website. If they are different, use the instructions provided on the website.

To use the product, follow these user functions and driving modes:

User Functions:

• DRIVING MODES:
  • F1 COMFORTABLE MODE
  • F2 SPORTS MODE
  • F3 RACING MODE
  • AU AUTO MODE
  • ECO FUEL SAVING MODE

Note : Select the appropriate driving mode based on your preferences and driving conditions.

Roadsafe Logo:
The “Roadsafe” logo represents the brand or manufacturer of the product.

INSTALLATION INSTRUCTIONS

IMPORTANT NOTES BEFORE INSTALLING

• The Throttle Controller is designed for specified vehicles only. Please make sure this is the correct product for your vehicle before you start the installation!
• All installation work should be done by a qualified professional to avoid damage to this product.
• All settings should be completed while the vehicle is stationary. For your own safety, please do not adjust while driving!

BEFORE INSTALLING, PLEASE CHECK OUR WEBSITE (ROADSAFE.COM.AU) FOR THE LATEST FITTING INSTRUCTIONS. IF THE TOP LEFT CORNER (V) NUMBER IS DIFFERENT TO WEBSITE, PLEASE USE INSTRUCTIONS FROM WEBSITE.

FITTING GUIDE

• Turn the ignition off and remove the car key. Leave the driver’s door open and wait 10 minutes.
  Note : Smart keys must be taken out of vehicle range.

• Locate the connector at the accelerator pedal and unplug it. For some vehicles, it may be easier to remove the accelerator pedal to access the wiring connector. During installation, do not touch the brake pedal or open and close doors as this may wake up vehicle systems and cause an error code.

• Plug the Throttle Controller connector into your accelerator pedal and then plug the vehicle side back into the Throttle Controller. Please plug the connectors in SLOWLY; this will help prevent any damage to the pins. Note: If the connector does not fit, STOP the installation and check that you have the correct product with your retailer!

• Plug the small white connector from the pedal harness into the Throttle Controller display, and find a suitable location on your dash to mount it. CAUTION: Please see below for connector orientation. DO NOT
  reverse these connectors!

• Cable tie any excess wiring so it’s out of the way and won’t affect the vehicle’s operation.
  (This is the installer’s responsibility!)

USER FUNCTIONS

Transmission select: auto or manual transmission must be selected first.

• Turn the ignition on and allow the Throttle Controller to power up.
• To select auto transmission, press and hold the up button for three seconds; the display should read “AAA”. Auto transmission is now selected.
• To select manual transmission, press and hold the down button for three seconds; the display should read “HHH”. Manual transmission is now selected.

Selecting driving modes:

• Press the mode button to cycle through modes » F1 Comfortable mode » F2 Sports mode » Fl Racing mode » AU mode » EC Fuel saving mode » Nor Normal mode [Factory].

DRIVING MODES

• F1 COMFORTABLE MODE
  • This mode is designed for smooth acceleration.
  • Adjustable sensitivity [1 >9]: use up/down keys to set sensitivity.
• F2 SPORTS MODE
  • This mode improves the instantaneous acceleration.
  • Adjustable sensitivity [1 >9]: use up/down keys to set sensitivity.
• F3 RACING MODE
  • This mode is designed for maximum acceleration.
  • Adjustable sensitivity [1 >9]: use up/down keys to set sensitivity.
• AU AUTO MODE
  • This mode is designed to study your driving style and adjust it, depending on the situation. This mode is a great way to set and forget as it will give both power and economy when needed.
• ECO FUEL SAVING MODE
  • This mode is designed for fuel saving with a slower and smoother acceleration.
  • Adjustable sensitivity [1 >9]: use up/down keys to set sensitivity.
• NORMAL MODE
  • In this mode, the vehicle reverts back to the factory settings. Not adjustable.

ANTI-THEFT FUNCTION
To prevent theft, the unit has a built-in immobilizer that will stop the vehicle from accelerating. To use this function, follow the steps below.

• Press the left and middle buttons for three seconds» and the display will show 000 » use all three buttons to set a three-digit password » press the left and middle buttons for three seconds » display will show LOC » Anti-theft function is now active.
• To disable anti-theft» turn ignition on » and enter your three-digit password » press the left and middle buttons for three seconds» The anti-theft has been disabled and the unit is back to normal operation.

TROUBLESHOOTING

Please note: If you are having problems with the installation of this product, please do not contact your retailer or Roadsafe until you have read ALL the troubleshooting notes below.

THROTTLE CONTROLLER RESETTING PROCEDURE

• Turn the ignition off and remove the car key. Smart keys must be taken out of vehicle range.
• Remove the Throttle Controller and return the vehicle back to its original state.
• Wait 10 minutes, then start the installation again (make sure the white display connectors are not reversed].
• After installation, turn the ignition on and start the vehicle. Check for any error codes on the dash and that the accelerator pedal is responding correctly.
• If error codes are still present and the accelerator pedal is not functioning correctly, please follow the pedal learning procedure below.

THROTTLE CONTROLLER PEDAL LEARNING PROCEDURE (Some vehicles will require pedal learning].

• Turn the ignition on only; do not start the engine.
• Press the up and down buttons together for about five seconds I up and down at the same time]. The Throttle Controller screen should show a 15-second countdown period. During this period, push the accelerator pedal in (making sure you press the pedal in as far as you can] and hold it there for about two seconds before letting go.
• Wait for the countdown to end. If l-00] is displayed, learning was successful. If 1-11] is displayed, learning was not successful and must be performed again.
• Start your engine and check for normal operation.
• If error codes are still present and the accelerator pedal is not functioning correctly, remove the device and contact your retailer.

FOR FURTHER ASSISTANCE EMAIL: SALES@ROADSAFE.COM.AU

SPECIFICATIONS

• Operating voltage 8v>18v
• Display Cable length: 1.4m
• Throttle Patch Lead Cable Length: 100mm (each side)
• Display dimensions: 54L x 11W x 35Hmm

KIT INCLUDES

• x1 Throttle Controller Display Unit
• x1 Throttle Controller Patch Lead
• x3 Cable Ties

WARRANTY TERMS & CONDITIONS

Roadsafe warrants this product against defects in factory workmanship and materials for the life of this product from the date of original purchase. This warranty applies to the first retail purchaser, is non-transferable, and covers only where the product has been subjected to normal use or service. Provision of this warranty shall not apply to any Roadsafe product that has been used for a purpose for which it is not designed, or altered in any way that would be detrimental to the performance or life of the product, misapplication, misuse, negligence or accident. Warranty claims to the manufacturer must be transportation prepaid and accompanied by dated proof of purchase. On any part or product found to be defective after examination by Roadsafe, Roadsafe will only repair or replace the merchandise through the original selling dealer or on a direct basis. Roadsafe assumes no responsibility for diagnosis, removal and/or installation labor, loss of vehicle use, loss of time, inconvenience or any other consequential expenses. The warranties herein are in lieu of any other expressed or implied warranties, including any implied warranty of suitability, and any other obligation on the part of Roadsafe or the selling dealer.
A division of Specialist Wholesalers Pty. Ltd. ABN 64163 280 279 VIC PH: 03 8687 1700 QLD PH: 07 3737 7420
Email : sales@roadsafe.com.au

References

• ROADSAFE.COM.AU

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>