AUTOSOLO ASWG001 Camber Caster Kingpin Gauge User Guide

AUTOSOLO ASWG001 Camber Caster Kingpin Gauge

Specifications

• Lever Gauge (D)
• Castor Gauge (B)
• Camber Gauge (A)
• King Pin Inclination Gauge (C)

Product Information
The Camber, Caster, and King Pin Inclination Gauge is a robust magnetic gauge designed for quick and accurate measurements of camber, caster, and king pin inclination. It is suitable for vehicles equipped with steel wheels and works best when used inconjunction with steering turntables, rear wheel level plates, and wheel clamps (ASWG001). The gauge comes in a durable composite plastic carry case for easy storage and protection.

Safety Instructions

1. Maintain the gauge in good condition.
2. Replace or repair any damaged parts.
3. Use the gauge on a level and solid ground for accurate measurements.
4. Do not allow untrained persons to operate the gauge.
5. When setting front-end alignment on commercial vehicles, never adjust drop arms or interconnecting links to avoid serious tire, wheel, and steering problems.
6. Any alignment changes necessary after using the equipment must] strictly adhere to the vehicle manufacturer’s recommendations.
7. Exercise common sense and caution while operating the gauge as it cannot cover all possible conditions and situations. Apply caution and make judgments accordingly.

Measuring Camber Angle

1. Drive vehicle forwards to centralize wheels.
2. Fit the gauge in the center of the vehicle’s wheel/hub/wheel clamp (ASWG001).
3. Set the Lever Gauge (D) bubble to the center and note the bubble position of the Camber Gauge (A).
4. Refer to the vehicle owner’s handbook before making any adjustments.
5. Note that adjustments to the caster or camber angles may affecteach other, so re-check all measurements after any adjustments are made.
6. Try to simulate normal running conditions during measurements, such as having a driver in the front driver’s seat or a half tank of gas.

CAMBER, CASTER & KINGPIN GAUGE

USER GUIDE

INTRODUCTION & SPECIFICATIONS

Overview
The Camber, Caster, and King Pin Inclination Gauge is a robust magnetic gauge designed for quick and accurate measurements of camber, caster, and king pin inclination. It is suitable for vehicles equipped with steel wheels and works best when used in conjunction with steering turntables, rear wheel level plates, and wheel clamps (ASWG001). The gauge comes in a durable composite plastic carry case for easy storage and protection.

Specifications

• Camber Gauge Graduation: ………………………………….. +5° to -5°
• Caster Gauge Graduation: ………………………………….. +11° to -3°
• King Pin Inclination Gauge Graduation: …………………… O to 14
• Magnetic Plate Diameter: ………………………………. 3.35” / 85mm

SAFETY INSTRUCTIONS

1. Maintain the gauge in good condition.
2. Replace or repair any damaged parts.
3. Use the gauge on a level and solid ground for accurate measurements.
4. Do not allow untrained persons to operate the gauge.
5. When setting front-end alignment on commercial vehicles, never adjust drop arms or interconnecting links to avoid serious tire, wheel, and steering problems.
6. Any alignment changes necessary after using the equipment must strictly adhere to the vehicle manufacturer’s recommendations.
7. Exercise common sense and caution while operating the gauge as it cannot cover all possible conditions and situations. Apply caution and make judgments accordingly.

NOTE: Remove the magnet protective plate before use.

MEASURING CAMBER ANGLE

NOTE! Before use remove magnet protective plate. Replace after use.

1. Drive vehicle forwards to centralise wheels.
2. Fit the gauge in the center of the vehicle’s wheel/hub/wheel clamp (ASWG001).
3. Set the Lever Gauge (D) bubble to the center and note the bubble position of the Camber Gauge (A).
4. Refer to the vehicle owner’s handbook before making any adjustments.
5. Note that adjustments to the caster or camber angles may affect each other, so re-check all measurements after any adjustments are made.
6. Try to simulate normal running conditions during measurements, such as having a driver in the front driver’s seat or a half tank of gas.

MEASURING CASTER ANGLE
Alignment Turntables (ASWG008) are recommended for this measurement to accurately turn your wheels to 20° in or out.

• Drive the vehicle forward so that the front wheels are positioned on alignment turntables (ASWG008) in the straight-ahead position, with the rear wheels on level plates (or additional turntables).
• Turn the front wheel to 20° OUT.
• Fit the gauge in the center of the wheel/hub/wheel clamp (ASWG001) and set the Lever Gauge (D) bubble to the center.
• Set the Castor Gauge (B) bubble to 0 by adjusting the thumb-turn screw underneath. Then, turn the front wheel to 20° IN.
• Set the Lever Gauge (D) bubble to the center again and read the bubble in the Castor Gauge (B) for the caster angle.
• Refer to the vehicle owner’s handbook before making any adjustments.
• Note that adjustments to the caster or camber angles may affect each other, so re-check all measurements after any adjustments are made.

MEASURING KING PIN INCLINATION

1. Drive the vehicle forward so that the front wheels are positioned on alignment turntables (ASWG008) in the straight-ahead position, with the rear wheels on level plates (or additional turntables).
2. Turn the front wheel to 20° OUT.
3. Fit the gauge in the center of the wheel/hub/wheel clamp (ASWG001) and set the Lever Gauge (D) bubble to the center.
4. Set the King Pin Inclination Gauge (C) bubble to 0 by adjusting the thumb-turn screw underneath. Then, turn the front wheel to 20° IN.
5. Read the bubble in the King Pin Inclination Gauge (C) for the degree of king pin inclination.
6. Refer to the vehicle owner’s handbook before making any adjustments.

Visit our website: autosolotools.com
For technical questions
please email or call us at: support@autosolotools.com
415.849.0275

©AutoSolo® 2023
All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of AutoSolo® 202

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>