genexis G2110 FiberBox Installation Guide

: August 21, 2024
: genexis

Table of Contents

G2110 FiberBox
Specifications:
Product Usage Instructions:
Installation:
Placement:
Connecting the FiberBox:
Port Overview:
LED Overview:
- FAQ:
Q: Is it safe to look directly into the fiber connector when

G2110 FiberBox

“`html

Specifications:

Product Name: FiberBox G2110
Placement Options: Desk placement, Wall mount
Ports: WAN port, LAN port, Power port
Buttons: ON/OFF button, Reset button (recessed)
Laser Safety: Class 1 Consumer Laser product

Product Usage Instructions:

Installation:

Label Position: The product label is positioned
on the back of the device.

Preparation: Ensure there is a power socket
within reach of where the device is being installed. Follow
instructions precisely to avoid damage to fiber optic
connectors.

Placement:

Desk Placement: Place the device horizontally
on a flat surface.

Wall Mount:

Download and print the drilling template from here.
Use the drilling template to drill holes, insert plugs, and put
screws into place.
Mount the device to the wall using the wall mount points on the
back of the FiberBox.

Connecting the FiberBox:

Open the green shutter from the WAN port, insert the fiber
patch cable from your fiber outlet into the WAN port.
Connect your gateway to the LAN port via an RJ45 network
cable.
Connect the supplied power adapter to the FiberBox and plug it
into a power socket.
Press the ON/OFF button to power on the device.

Warning: Do not look directly into the fiber
connector when the product is powered on.

Port Overview:

Reset button (recessed)
Power port
WAN port
LAN port
ON/OFF button

LED Overview:

Reset Button: Press and release to reset; press
and hold for factory reset.

FAQ:

Q: Is it safe to look directly into the fiber connector when

the product is powered on?

A: No, it is advised not to look directly into
the fiber connector when the product is powered on due to the laser
emission.

“`

FiberBox
G2110
Installation Guide

Installation guide
Box contents · Genexis FiberBox · Power adapter · Labels (self-adhesive)
Label position The product label is positioned on the back of the device.
Preparation Ensure there is a power socket within reach of where the device is being installed.
Important: Instructions need to be followed precisely and uninterrupted. This minimizes the risk of damage to the fiber optic connectors, causing a severe degradation of signal quality.

Placement The product supports two placement options; desk placement and mounted to a wall. It is recommended to place the device `away’ from obstacles and objects.
Desk placement 1. Place the device horizontally
on a flat surface.
Wall mount 1. Download and print the
drilling template from https:// genexis.eu/product/fiberbox/ downloads 2. Use the drilling template to drill holes, insert plugs and put screws into place. 3. Use the wall mount points on the back of the FiberBox to mount the device to the screws.

Connecting the FiberBox 1. Open the green shutter from
the WAN port, insert the fiber patch cable from your fiber
outlet into the WAN port. 2. Connect your gateway to the
LAN port via an RJ45 network cable. 3. Connect the supplied power adapter to the FiberBox and
plug the adapter into a power socket. 4. Press the ON/OFF button to power on the device.

Warning: This product contains a laser that emits invisible light. It is a Class 1 Consumer Laser product according to EN 50689:2021, which means it is safe under all conditions of normal use. However, it is still advised to not look directly into the fiber connector when the product is powered on.
Warning: Do not cover the device, this will interfere with the ventilation. Ambient Operating Temperature: 0°C ~ 40°C

Port overview

Reset button Power port

WAN port

LAN port

ON/OFF button

ON/OFF button Power ON or OFF press and release to switch device ON or OFF

Reset button (recessed) Reset – press and release Factory reset – press and hold the button until System and Uplink LED start to blink

LED overview
System Green system ok Green (blinking) booting Red – system or boot failure Red (blinking) – insufficient PON signal Off power off
Uplink Green link ok Green (blinking) link establishing Off no link
System + Uplink Green (blinking) firmware upgrade

EU Declaration of Conformity

Hereby, Genexis Netherlands B.V. declares that the product FiberBoxG2110 is in compliance with Directives 2014/30/EU, 2014/35/EU, 2011/65/EU, Delegated Directive 2015/863 and Ecodesign Directive 2009/125/EC.

The full text of the EU declaration of conformity is available at the following internet address: https://genexis.eu/product/fiberbox/red/ fiberbox-g2110

Company Name Genexis Netherlands B.V.

Signature of authorized person

Company Address Lodewijkstraat 1a 5652 AC Eindhoven The Netherlands

Name and title of authorized person Maarten Egmond, CTO

Place of issue Eindhoven
The Netherlands

Date of issue 2023-12-20

Revision 1.0- December 2023 – Copyright © 2023 Genexis Netherlands B.V. All rights reserved.
Multiple languages of this document and additional product information are available on https://genexis.eu/product/fiberbox/downloads Genexis assumes no responsibility for any inaccuracies in this document. Genexis reserves the right to change, modify, transfer, or otherwise revise this publication without notice.