ROADSAFE RP-CRU70EV2 Recovery Tow Points User Manual
- June 13, 2024
- ROADSAFE
Table of Contents
ROADSAFE RP-CRU70EV2 Recovery Tow Points
Product Information
- Product: Rated Recovery Point
- Product Code: RP-CRU70EV2
- Vehicle: Toyota Landcruiser 76/78/79 Series (excluding 79 ANCAP S/C)
- Manufacturer: Roadsafe
- Website: www.roadsafe.com.au
FITTING INSTRUCTIONS
- VEHICLE Toyota Landcruiser 76/78/79 Series (excluding 79 ANCAP S/C)
- PRODUCT Rated Recovery Point
- PRODUCT CODE RP-CRU70EV2
DURING RECOVERY ALWAYS USE BOTH RECOVERY POINTS
For ease of fitting, we recommend
- Read the fitting instructions in their entirety.
- Elevate the vehicle and ensure it is safely supported.
- Remove the front plastic undertray or aftermarket bash plate
To begin the installation, identify the following parts
DRIVER SIDE| | PASSENGER SIDE|
---|---|---|---
Main Recovery Plate| 1| Main Recovery plate| 1
9mm Spacer
(Not required for ANCAP single cab 79)
| 1| 9mm Spacer
(Not required for ANCAP single cab 79)
| 1
M12 x 120L Bolt, lock nut, and 2x washers| 1| M10 x 110L Bolt, lock nut, and
2x washers| 1
M10 x 60L Bolts| 2| M10 x 60L Bolts| 2
M10 x 40L Bolts| 1| M10 x 40L Bolts| 1
M10 Split washer + Flat washer| 3 pairs| M10 Split washer + Flat washer| 4
pairs
23X10.5×2 Washer| 2| 23X10.5×2 Washer| 2
26X10.8×4 Washer| 2| 26X10.8×4 Washer| 2
| | Crush tube| 1
ENSURE ALL SUPPLIED AND SPECIFIED COMPONENTS ARE USED DURING THE INSTALLATION OF TOW RECOVERY POINTS, FAILURE TO DO SO WILL SIGNIFICANTLY REDUCE THE WORKING LOAD LIMIT (WLL) SPECIFIED FOR EACH INDIVIDUAL POINT, WHICH CAN RESULT IN SERIOUS INJURY OR DEATH.
DURING RECOVERY ALWAYS USE BOTH RECOVERY POINTS
-
The Mounts themselves are sided, so please ensure installation to the correct side of the vehicle. After removing the undertray or bash plate undo the lower front steering box bolt and position plate as per.
Note: The 25mm x 9mm yellow spacer is to be used in all applications except ANCAP-rated 79 single cab models. -
On the driver’s side, use the M12 x 120mm bolt and 25mm x 9mm (see note) spacer to replace the factory steering box mounting bolt.
-
Use 2 M10 x 60mm bolts for the 2 lower holes which are spaced from the chassis and the M10 x 40mm for the hole against the chassis.
-
There are two different thickness washers to account for different front bar mount brackets, it is the discretion of the fitter to ensure the recovery point is evenly contacting the chassis rail at all points.
-
Continue to the passenger side, positioning the plate as per.
-
Insert the crush tube and the M10 x110mm bolt into the top-rear mounting hole, again use 2 M10 x 60mm bolts for the 2 lower holes which are spaced from the chassis, and the M10 x 40mm for the hole against the chassis.
-
All models have nuts retained in the chassis on both sides, ready for fitment.
-
Ensure all bolts are fitted and torqued to recommended settings to ensure tow points meet tested standards.
Bolt Torque Specs
| 8.8| 10.9| 12.9
---|---|---|---
M10| 41-60Nm| 59-85Nm| 65-94Nm
M12| 71-105Nm| 102-150Nm| 114-164Nm
RECOMMENDED FOR 4WD SPECIALIST MECHANICS TO FIT
- The RP-CRU70E has been designed to protrude next to the Roadsafe Skid Plate as shown in images 1 & 2 above.
- With some aftermarket skid plates, you might need to trim two 100mm (long) x 40mm (wide) holes on each side to allow for the skid plate to be refitted. For the original Toyota undertray, 2 small notches need to be done as per images 3 and 4.
A division of Specialist Wholesalers Pty. Ltd. ABN 64 163 280 279
- VIC PH: 03 8687 1700 | QLD
- PH: 07 3737 7420 |
- Email: sales@roadsafe.com.au
- roadsafe.com.au
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>