FORTIN Dodge RAM 2008 Standard Key Remote Starters and Alarm Systems Installation Guide
- June 13, 2024
- FORTIN
Table of Contents
FORTIN Dodge RAM 2008 Standard Key Remote Starters and Alarm Systems
Product Information
| Product Name | Dodge RAM 2008 Vehicle Bypass Module |
|---|---|
| Model Number | Guide #63751 |
| Firmware Version | 74.38 (minimum) |
Product Usage Instructions
- Connect the FLASH LINK UPDATER or FLASH LINK MOBILE tool (sold separately) to add firmware version and options.
- Program the bypass option by following these steps:
- Program the functionality of the hood contact by setting UNIT OPTION OPTION UNITE C1 to A11.
- Program the remote starter option for R.S. OEM REMOTE STAND ALONE by setting FUNCTION FONCTION 31 to 38 MODE 42.
- Enable Press 3x Lock to remote start with the OEM remote.
- Install the required parts (not included) for the remote starter option:
- 1X Fuse
- 1X Resistor
- Mandatory Insta llation:
- Install the hood pin contact (included) if the vehicle can be remote started with the hood open. Set function A11 to OFF.
- Attach the security sticker (included).
- Ensure that the module is installed by a qualified technician to avoid permanent damage to the vehicle.
- Wiring Connection:
| Wire Color | In/Out | Description |
|---|---|---|
| Yellow | In | Ignition |
| Purple | Out | Parking Lights (+) |
| Pink | Out | Hood Pin (-) |
| White | Out | 12V (+) |
| Orange | Out | Accessory (+) |
| Green | Out | Function AA44 |
| Red/Blue | In | Function AA99 |
- Cut the loop for automatic transmission mode.
- Connect the CAN wires:
- CAN LOW: White
- CAN HIGH: White/Orange
- Connect the 6-PIN Main harness (White connector) by following these steps:
- Press and hold the programming button.
- The Blue, Red, Yellow, and Blue & Red LEDs will alternatively illuminate.
- Release the programming button when the LED is BLUE.
- If the LED is not solid BLUE, disconnect the 6-Pin connector (Main-Harness) and go back to step 1.
Vehicle functions
HARDWARE VERSION
- 7 MINIMUM****
BYPASS
- FIRMWARE VERSION
- 74.[38]
- CHRYSLER/ DODGE/JEEP/ MITSUBISHI MINIMU
To add the firmware version and the options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately.
- Program bypass option:
- IF THE VEHICLE IS NOT EQUIPPED WITH FUNCTIONAL HOOD PIN:
- Program bypass option (If equiped with OEM alarm):
UNIT OPTION OPTION UNITE/DESCRIPTION
- C1/ OEM Remote status (Lock/Unlock) monitoring
- A11/OFF NON/Hood trigger (Output Status).
- D2/Unlock before / Lock after (Disarm OEM alarm)
Program remote starter option:
Program remote starter option for R.S. OEM REMOTE STAND ALONE:
FUNCTION/MODE/DESCRIPTION
- 31/4//(+) Parking Light (E1) (+) Accessory (E2)
- 38/2//Enable Press 3x Lock to remote start with the OEM remote.
Parts required
Parts required (Not included)
- 1X Fuse
- 1X Resistor
MANDATORY INSTALL
- NON PIN
- HOOD STATUS: THE HOOD PIN SWITCH (INCLUDED) MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.
- A11 OFF NON
SECURITY STICKER
Notice: the installation of safety elements are mandatory. The hood pin and the sticker are essential security elements and must be installed. THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.
WIRING CONNECTION
KEY BYPASS
KEY BYPASS PROGRAMMING PROCEDURE
REMOTE STARTER
REMOTE STARTER PROGRAMMING PROCEDURE
REFER TO THE QUICK INSTALL GUIDE INCLUDED WITH THE MODULE FOR THE REMOTE
STARTER PROGRAMMING.
REMOTE STARTER FUNCTIONALITY
Notice: Updated Firmware and Installation Guides Updated fi rmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest fi rmware and download the latest installation guide(s) prior to the installation of this product.
WARNING
The information on this sheet is provided on an (as is) basis with no
representation or warranty of accuracy whatsoever. It is the sole
responsibility of the installer to check and verify any circuit before
connecting to it. Only a computer safe logic probe or digital multimeter
should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or
responsibility whatsoever pertaining to the accuracy or currency of the
information supplied. The installation in every caseis the sole responsibility
of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no
liability or responsibility whatsoever resulting from any type of
installation, whether performed properly, improperly or any other way. Neither
the manufacturer or distributor of this module is responsible of damages of
any kind indirectly or directly caused by this module, except for the
replacement of this module in case of manufacturing defects. This module must
be installed by qualifi ed technician. The information supplied is a guide
only. This instruction guide may change without notice. Visit
www.fortinbypass.com. to get the latest
version.
CONTACT
- TECH SUPPORT
- Tel: 514-255-HELP (4357)
- 1-877-336-7797
- ADDENDUM GUIDE WEB UPDATE | MISE À JOUR INTERNET
- www.fortinbypass.com.
- INTERFACE MODULE
- Made in Canada
- PATENTS PENDING US: 2007-228827-A1
- www.fortinbypass.com.
- HARDWARE VERSION
- FIRMWARE VERSION
- Date: xx-xx
- REV.: 20230609
This guide may change without notice. See www.fortin.ca. for latest version.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>