FORTIN 111621 THAR-SUB4 Tharness for Remote Start Data Modules Installation Guide

![FORTIN 111621 THAR SUB4 Tharness for Remote Start Data Modules

• Evo All](https://manuals.plus/wp-content/uploads/2023/09/FORTIN-111621-THAR- SUB4-Tharness-for-Remote-Start-Data-Modules-Evo-All.jpg)GUIDE # 111621
  THAR-SUB4 THARNESS INSTALLATION
  ADDENDUM – SUGGESTED WIRING CONFIGURATION

111621 THAR-SUB4 Tharness for Remote Start Data Modules

SUBARU
Ascent| Push-to-Start| 2023

Vehicle functions supported in this diagram (functional if equipped)

Immobilizer bypass

Lock
Unlock
Arm
Disarm
Trunk (open)
Parking Lights
Heated Seats| AUX.1 :
Rear Defrost
RAP Shutdown
Tachometer
Door Status
Trunk Status
Hand-Brake Status
Foot-Brake Status
Secure Take Over
| COMPATIBLE MODULE REQUIRED:| QR CODE ON THE LABEL| FIRMWARE VERSION
93.[01] MINIMUM| To add the firmware version and the options, use the
FLASH LINK UPDATER or FLASH LINK MOBILE tool,
sold separately.
---|---|---|---|---
 MANUFACTURED AFTER: 2019
| Program bypass option:| UNIT OPTION| DESCRIPTION
---|---|---|---
C1| OEM Remote status (Lock/Unlock) monitoring
| D6| Push-to-Start
IF THE VEHICLE IS NOT EQUIPPED WITH FUNCTIONAL HOOD PIN:| | Hood trigger (Output Status).
| Program bypass option (For RAP shutdown):| D5| Lock after start

NOTES
MAKE SURE THE KEY IS NOT INSIDE THE CAR WHEN REMOTE STARTING.
Parts required (Not included)
1X 1 AMP Diode
**MANDATORY INSTALL

• HOOD PIN
  HOOD STATUS : THE HOOD PIN SWITCH MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.
  Notice:** the installation of safety elements are mandatory. The hood  in is an essential security element and must be installed.
  THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.

AUTOMATIC TRANSMISSION WIRING CONNECTION

KEY BYPASS PROGRAMMING PROCEDURE

OEM remote| Keep
the other OEM remotes away from the vehicle.
Minimum 3 meters (10 feet).
---|---
| Press and hold the Insert programming button: the 4-Pin (Data-Link) connector.
9 The Blue, Red, Yellow and Blue & Red LEDs will alternatively illuminate.
| Release the programming button when the LED is BLUE.
If the LED is not solid BLUE disconnect the 4-Pin connector (Data-Link) and go back to step 1.

| Insert the required remaining connectors.
| Do not press the brake pedal.
Press the START/STOP button twice to turn ON the ignition.
| Press and release the programming  button once (1x).
9 The BLUE LED will turn off.
9 The BLUE LED will flash rapidly.
| 9 The BLUE LED will turn ON solid.
Press the START/STOP button once to turn OFF the ignition.
| Remove the battery from 1 OEM remote.
Keep the other OEM remotes away from the vehicle. Minimum 3 meters (10 feet).
| Place the OEM remote (no battery) close to the front of START/STOP button as shown.
| Press the footbrake pedal.
9 The vehicle ignition will turn ON.
9 The RED RED will turn ON.
9 The RED BLUE will turn OFF.
Release the pedal.
| Press the START/STOP button once to turn OFF the ignition.
| Place the OEM remote (no battery) close to the front of START/STOP button as shown.
| Press the footbrake pedal.
9 The vehicle ignition will turn ON.
The YELLOW LED will turn ON.
9 The RED LED will turn OFF.
9 Release the pedal.
| 9 The RED and YELLOW LEDs  will alternated.
Press the START/STOP button once to turn OFF the ignition.
| Disconnect all the connectors and after the Data-Link (4-pins) connector.
| Use the tool:
FLASH LINK UPDATER or FLASH LINK MOBILE to visit the DCryptor menu.
*Parts required (not included)
| AFTER DCRYPTOR PROGRAMMING COMPLETED
Go back to the vehicle and reconnect the 4-Pin (Data-Link) connector and after, all the remaining connector.
The module is now programmed.| REMOTE STARTER / ALARM VERIFICATION
PROCEDURE  Test the remote starter. Remote start the vehicle.

FUNCTIONS

The engine will shutdown when a door is open if the vehicle is not Unlock.

Module label

Notice: Updated Firmware and Installation Guides
Updated fi rmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest fi rmware and download the latest installation guide(s) prior to the installation of this product.
WARNING
The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualifi ed technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.
This guide may change without notice. See www.fortin.ca for latest version.

  TECH SUPPORT
Tel: 514-255-HELP (4357)
1-877-336-7797
ADDENDUM GUIDE
www.fortinbypass.com
WEB UPDATE

Documents / Resources

| FORTIN 111621 THAR-SUB4 Tharness for Remote Start Data Modules [pdf] Installation Guide
EVO-ALL, THAR-SUB4, 111621, 111621 THAR-SUB4 Tharness for Remote Start Data Modules, THAR-SUB4 Tharness for Remote Start Data Modules, Tharness for Remote Start Data Modules, Remote Start Data Modules
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>