FORTIN 2011 Standard-Key Remote Starters and Alarm Systems Installation Guide

FORTIN 2011 Standard-Key Remote Starters and Alarm Systems

Product Information

• Product Name: THAR-GM7 Tharness Installation
• Product Compatibility: Chevrolet Camaro Flip-key 2010-2015

Product Features

• Immobilizer bypass
• Lock/Unlock
• Arm/Disarm
• Trunk (open)
• RAP Disable
• Tachometer
• Door Status
• Trunk Status
• Hood Status
• Hand-Brake Status
• Foot-Brake Status
• PK3, Passlock OEM remote Monitoring
• R.S. OEM remote Stand Alone compatible

Product Usage Instructions

• To install the THAR-GM7 Tharness, follow the steps below:
  • Ensure that the vehicle is compatible with the product (Chevrolet Camaro Flip-key 2010-2015).
  • Use the supplied FLASH LINK UPDATER or FLASH LINK MOBILE tool to add the firmware version and options.
  • If the vehicle can be remote started with the hood open, install the included Hood Pin Switch and set Function A11 to OFF.
  • Make sure to read and follow all the instructions provided in the user manual for proper installation.
• For programming bypass options, follow these steps:
  • Program the bypass option by selecting UNIT OPTION C1 or D2.
  • The option “Unlock before / Lock after (Disarm OEM alarm)” is activated by default.
• For programming remote starter option for R.S. OEM REMOTE STAND ALONE, follow these steps:
  • Select FUNCTION FONCTION 38.
  • Set it to OFF by default.
• Note that the vehicles Flip-key remote will not be functional during remote start.
• Additional parts required for installation (not included)
  • 1X 180 Ohm resistor (Manual transmission)
  • 1X 1Amp. diode (Manual transmission)
• This module must be installed by a qualified technician. Incorrect connections can cause permanent damage to the vehicle.

Important Safety Information

• Warranty will be void if the product is opened.
• Ensure that the product is installed by a qualified technician to avoid any damage to the vehicle.

Note: The provided information is based on the text-extract from the user manual.
For detailed and accurate instructions, please refer to the complete user manual included with the product.

REGULAR AND THAR-GM7 THARNESS INSTALLATION

**MANDATORY INSTALL

• HOOD PIN
  HOOD STATUS :** THE HOOD PIN SWITCH MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.

Notice: the installation of safety elements are mandatory. The hood pin is an essential security element and must be installed.
THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.

DESCRIPTION

AUTOMATIC TRANSMISSION WIRING CONNECTION

DCRYPTOR PROGRAMMING PROCEDURE

PARTS REQUIRED (NOT INCLUDED)
1x FLASH LINK UPDATER,
1x FLASH LINK MANAGER
SOFTWARE | PROGRAMME
Microsoft Windows Computer with Internet connection Ordinateur Microsoft Windows avec connection Internet

1x FLASH LINK MOBILE
1x FLASH LINK MOBILE APP
Smartphone AndroId or iOS with Internet connection (provider charges may apply).

BEFORE PROGRAMMING SET THE UNIT OPTIONS AND SAVE.

1. Press and hold the programming button: Connect the 4-PIN Data-link harness (Black connector).
   The LEDs will alternate between BLUE, RED, YELLOW & BLUE/RED flashes

2. Release the programming button when the LED is YELLOW.
   If the LED is not solid YELLOW disconnect the 4 Pin connector (Data-Link) and go back to step 1

3. Insert the required remaining connectors

4. Press release and the programming button five times (5x).
   The YELLOW LED will alternate between 5x flashes and a pause. until the YELLOW LED turns ON

5. Turn ignition (ON). the Ignition to the ON/RUN position.
   The RED LED will turns ON.
   The YELLOW LED turns OFF
   If the LED is not solid RED disconnect the 4 Pin connector (Data-Link) and go back to step 1.

6. Turn the Ignition to the OFF position.

7. Remove the key from the ignition barrel.

8. Wait 5 seconds.

9. Turn the Ignition to the ON position.
   The BLUE LED will turns ON.
   Wait,  the BLUE & RED LED will turn OFF.
   Wait, he YELLOW LED will Flash.
   Wait he YELLOW LED will turn OFF.
   Wait he BLUE LED will Flash rapidly.
   If the LEDs do not react as shown, the 6-Pin connector (Main-Harness) and go back to step 1.

10. Turn the Ignition to the OFF position. the BLUE LED flash slowly.

11. Disconnect all connectors and after the 6-Pin (Main-Harness) or the 4-Pin Data-link connector.

12. Use the tool: FLASH LINK UPDATER or FLASH LINK MOBILE to visit the DCryptor menu.
    *Parts required (not included)

13. AFTER DCRYPTOR PROGRAMMING COMPLETED Go back to the vehicle and reconnect the 6-Pin (Main- Harness) or the 4-pins (Data-Link) connector and after all the remaining connector.

The module is now programmed.
REMOTE STARTER / ALARM VERIFICATION
Test the remote starter. Remote start the vehicle

REMOTE STARTER FUNCTIONALITY

MANUAL TRANSMISSION: READY MODE –
BY DEFAULT

• The vehicle must be running.

• Make sure that all doors are closed and the transmission is in the NEUTRAL position.

• Press the brake pedal.

• Engage the parking brake.

• Release the brake pedal.

• Press the START button for 3 seconds.
  The parking lights will flash once and then remain on.

• Remove the keyfrom the ignition barrel : the vehicle will remain running with the Remote-Starter.

• Exit the vehicle and close all of the doors. The engine will stop running once all the doors are closed.

• Ready mode is now active, remote start is functional. If one of the doors is open the mode will be disabled.

CHOICE 2 – CHOIX 2

• The vehicle must be running.
• Make sure that all doors are closed and the transmission is in the NEUTRAL position.
• Press the brake pedal.
• Engage the parking brake.
• Release the brake pedal.
• Press the START button for 3 seconds. The parking lights will flash once and then remain on.
• Remove the key from the ignition barrel : the vehicle will remain running with the Remote-Starter.
• Exit the vehicle and close all of the doors.
• Lock the doors with the remote-starter remote or the OEM remote. The engine will stop running.
• Ready mode is now active, remote start is functional. If one of the doors is open the mode will be disabled.

CHOICE 3 – CHOIX 3

• The vehicle must be running.
• Make sure that all doors are closed and the transmission is in the NEUTRAL position.
• Press the brake pedal.
• Engage the parking brake.
• Release the brake pedal.
• Remove the key from the ignition barrel : the vehicle will remain running with the Remote-Starter.
• Exit the vehicle and close all of the doors. The engine will stop running once all the doors are closed.
• Ready mode is now active, remote start is functional. If one of the doors is open the mode will be disabled.

TAKE OVER AUTOMATIQUE TRANSMISSION

• All doors must be closed.
• Remote start the vehicle.
• Unlock the doors with the remote-starter remote or the OEM remote.
• Insert and Turn the key to the Ignition ON/RUN position.
• Press the brake pedal.
• The vehicle can now be put in to gear and driven.

REMOTE STARTER PROGRAMMING PROCEDURE

REFER TO THE QUICK INSTALL GUIDE INCLUDED WITH THE MODULE FOR THE REMOTE STARTER PROGRAMMING.

Notice: Updated Firmware and Installation Guides
Updated firmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest firmware and download the latest installation guide(s) prior to the installation of this product.

If the vehicle is not unlocked with one of these conditions the remote-starter will shut down as soon as any door is opened.

WARNING
The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN

ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualified technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.
Copyright © 2006-2018, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED PATENT PENDING

TECH SUPPORT
Tél: 514-255-HELP (4357)
1-877-336-7797
ADDENDUM GUIDE
www.fortinbypass.com
WEB UPDATE

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>