FORTIN 102991 2017 Volkswagen Golf R Push Button Remote Starters and Alarm Systems Installation Guide

: June 13, 2024
: FORTIN

Table of Contents

STAND ALONE INSTALLATION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

FORTIN logo1 FORTIN - EVO ALL 1 REV.: 20211020 Guide # 102991

STAND ALONE INSTALLATION

ADDENDUM – SUGGESTED WIRING CONFIGURATION

ONLY COMPATIBLE WITH AUTOMATIC TRANSMISSION VEHICLES.

| Vehicle functions supported in this diagram (functional if equipped)
---|---
| Immobilizer bypass with TB-VW (Sold separately)| T-Harness available (sold separately)| Lock| Unlock| Arm| Disarm| Hazard Lights| Tachometer|

AUX.1 Comfort Group

Push-to-Start

| 2015-2018|

•

| •| •| •| •| •| •| •| •| •| •| •| •| •| •|

•

|

COMPATIBLE MODULE REQUIRED:

|

QR CODE ON THE LABEL

|

FIRMWARE VERSION

64.[06]

MINIMUM

|

To add the firmware version and the options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately.

---|---|---|---|---

MANUFACTURED AFTER: 2019

| Parts required (Not included)
---|---
| 2x 1 Amp. Diodes
1x 7 Amp. Fuse
| 1x TB-VW (key bypass)
| PROGRAMMING TOOL REQUIRED for key bypass programming.
Sold separately
---|---
WARNING

| Vehicle’s equipped with Virtual Cluster, not supported for the key bypass.
MANDATORY INSTALL

* HOOD PIN

CONTACT

HOOD STATUS : THE HOOD PIN SWITCH (INCLUDED) MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.

| A11|

Notice: the installation of safety elements are mandatory. The hood pin is an essential security element and must be installed.

THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.

This guide may change without notice. See www.fortin.ca for latest version.

NOTES

|

Program bypass option:

|

UNIT OPTION

| DESCRIPTION
---|---|---|---

C1

| OEM Remote status (Lock/Unlock) monitoring
|

D6

| Push-to-Start
Program bypass option
(If equipped with OEM alarm):|

D2

| Unlock before / Lock after (Disarm OEM alarm)

IF THE VEHICLE IS NOT EQUIPPED WITH FUNCTIONAL HOOD PIN:

|

A11

| | Hood trigger (Output Status).

PARTS REQUIRED (NOT INCLUDED)

1x ,

1x

1x Microsoft Windows Computer with Internet connection

OR

1x

1x Smartphone Android or iOS with Internet connection (provider charges may apply).

MANDATORY

HOOD PIN

CONTACT

| REMOTE START SAFETY OVERRIDE SWITCH

VALET SWITCH

Part #: RSPB available, Sold separately.

Notice: the installation of safety elements are mandatory. The hood pin and the valet switch are essential security elements and must be installed.

STAND ALONE CONFIGURATION

|

Program bypass option OEM Remote Stand Alone Remote Starter:

| |
---|---|---|---

D1.1

| LOCK, UNLOCK, LOCK
|

Program bypass option with oem remote:

|

UNIT OPTION

| DESCRIPTION
---|---|---|---

C1

| OEM Remote Monitoring
|

Program bypass option with RF KIT antenna:

|

UNIT OPTION

| DESCRIPTION
---|---|---|---

H1 to H6

| Supported RF Kits and select RF Kit

REMOTE STARTER FUNCTIONALITY

All doors must be closed.

Press the OEM remote’s Lock Unlock Lock buttons to remote-start (or remote-stop) the vehicle.

The vehicle will START.

REMOTE STARTER DIAGNOSTICS

MODULE RED LED
x2 flash :| Brake ON
x3 flash :| No tach
x4 flash :| Ignition before start
x5 flash :| Hood Open

REMOTE STARTER WARNING CARD

CUT THIS WARNING CARD AND STICK IT ON A VISIBLE PLACE:
or use the package RSPB , Sold separately

| WARNING
---|---
REMOTE STARTER

THE VEHICLE CAN BE STARTED BY EITHER: PRESSING THE LOCK BUTTON ON THE OEM REMOTE 3 TIMES CONSECUTIVELY OR BY A SMARTPHONE. TURN ON THE SAFETY SWITCH LOCATED UNDER THE DASHBOARD BEFORE WORKING ON THE VEHICLE.

DESCRIPTION

(1) Under the steering column
(2) Under steering column cover.
(3) VESCM – Electrical System Control Module under dash driver side, above Driver Kick Panel
(4) OBD-II connector

Pull the clips to release the cover of the connector.

FORTIN - Pull the clips

Clips

AUTOMATIC TRANSMISSION WIRING CONNECTION

(1) Under the steering column – Black connector – Back view
(2) Back view Black 2-Pin connector transponder connector
(3) Brown cover Under the dash Driver side, Black 73-PINS connector – Back view
VESCM – Electrical System Control Module under dash driver side, above Driver Kick Panel
(4) OBDII Front view

DCRYPTOR PROGRAMMING PROCEDURE

FORTIN - D CRYPTOR TECHNOLOGY

Parts required (not included)

1x ,

1x

1x Microsoft Windows Computer with Internet connection

OR

1x

1x Smartphone Android or iOS with Internet connection
(Internet provider charges may apply)

BEFORE PROGRAMMING SET THE UNIT OPTIONS AND SAVE.

[1]

Take out the battery from the remote control.

[2]

Place the transponder’s ring in front of the remote control.

[3]

With the remote beside the antenna ring, proceed with the programming on the next pages.

[4]

*USE THE R-LINK TOOL FOR PROGRAMMING*
Sold separately

Connect the R-LINK instead of the TB-VW.

(~) RX White or Lt.Blue/Black
(~) TX Blue or Lt.Blue
Ground Black
(+)12V Red
White/Red or Green
White/Green or Green/Black

[5]

WARNING:
Close and open the driver door.

KEY BYPASS PROGRAMMING PROCEDURE

[6]

Press and hold the programming button:
Connect the 4-Pin Data-link connector.

The BLUE, RED, YELLOW and BLUE & RED LEDs will alternatively illuminate.

[7]

Release the programming button when the LED is BLUE.

If the LED is not solid BLUE disconnect the 4-Pin connector (Data-Link) and go back to step 1.

[8]

Insert the required remaining connectors.

[9]

Press the Push-to-Start button to turn ON the ignition.

[10]

Press and release the programming button once (1x).

The BLUE LED will turn off.

Wait,

The BLUE LED will flash rapidly.

[11]

Press and hold the programming button.

The BLUE LED will turn OFF.

Wait,

The RED LED will turn ON.

Release the programming button.

[12]

WAIT,
this process may take up to 5 minutes

Wait , do not touch the vehicle or the module.

The BLUE, RED and YELLOW LEDs will rapidly alternate.

the RED LED to turn ON.

Wait,

the YELLOW LED will flash once.

[13]

Wait,

Wait for the RED and YELLOW LEDs to slowly alternate.

If the RED LED flashes slowly, the programming has failed, go back to step1 and start the programming over.

[14]

Press the Push-to-Start button once to turn off the ignition.

[15]

Disconnect all the connectors and after the Data-Link (4-pins) connector.

[16]

Microsoft Windows Computer with Internet connection*

[OR]

VEHICLE’S OBDII CONNECTOR
Smartphone*
(Internet provider charges may apply)

Use the tool:
FLASH LINK UPDATER or FLASH LINK MOBILE to visit the DCryptor menu.

*Parts required (not included)

[16]

AFTER DCRYPTOR PROGRAMMING COMPLETED
Go back to the vehicle and reconnect the 4-Pin (Data-Link) connector and after, all the remaining connector.

NOTE
IF PROGRAMMING IS INTERRUPTED DURING THE PROCESS, SUCH AS A MODULE IS DISCONNECTED OR BY TURNING OFF THE IGNITION WITH THE KEY, IT IS POSSIBLE THAT THE VEHICLE WILL NO LONGER START NORMALLY, YOU MUST DISCONNECT AND RECONNECT THE VEHICLE BATTERY TO CORRECT THE SITUATION.

[18]

Take out the remote control from the transponder’s ring.

[19]

Insert the battery into the remote control.

[20]

Connect the TB-VW instead of the R-LINK.

(~) RX White or Lt.Blue/Black
(~) TX Blue or Lt.Blue
Ground Black
(+)12V Red
White/Red or Green
White/Green or Green/Black

The module is now programmed.

REMOTE STARTER / ALARM VERIFICATION PROCEDURE

Test the remote starter. Remote start the vehicle.

REMOTE STARTER FUNCTIONALITY

All doors must be closed.

Remote start the vehicle.

Unlock the doors with either:
• The OEM remote
• The remote-starter remote.

Enter the vehicle with the Intelligent SmartKey.

The vehicle can now be put in to gear and driven.

Module label

Notice: Updated Firmware and Installation Guides
Updated firmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest firmware and download the latest installation guide(s) prior to the installation of this product.

WARNING
The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualified technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.

FORTIN - TECH SUPPORT